cecotec DRUMFIT INDOOR EOLO Manual De Instrucciones página 29

ENGLISH
the device.
2. BEFORE USE
- This appliance is packaged in a way as to protect it during transport. Take the device out
of its box and remove all packaging materials. You can keep the original box and other
packaging elements in a safe place. This will help you prevent damage to the device when
transporting it in the future. In case the original packaging is disposed of, make sure all
packaging materials are recycled accordingly.
- Make sure all parts and components are included and in good conditions. If there is any
piece missing or in bad conditions, contact the official Cecotec Technical Support Service
immediately.
Box content
- DrumFit Indoor Eolo stationary bike
- Assembly kit
- Instruction manual
- Power adapter
- Chest strap heart-rate monitor
- CR2032 battery for the heart-rate band
3. ASSEMBLY
Remove all parts from the packaging, put them on the floor and check that none are missing.
Please note that some parts are already installed on the main frame. In addition, there are
some parts that are connected with individual parts. This will make assembly quicker and
easier for you.
STEP 1. Fit the stabilisers (Fig. 2)
1.
Fix the front stabiliser (8) to the main frame (6). To do this, use two Allen bolts (14), two
pressure washers (15) and two curved washers (16). Repeat the process with the rear
stabiliser (9).
2.
You can adjust the height of the handlebar stem (4) and saddle post (10) with the L-shaped
adjustment knob (5). Loosen it, set the saddle post to the desired height, and retighten it.
STEP 2. Fit the pedals and the saddle (Fig. 3)
1.
The pedals (7L+7R) have a mark: the right pedal has an R, and the left one an L. Note:
the reference (right/left) is taken as if the user was sitting on the saddle. Put each pedal
(7L+7R) on its corresponding crank. (Note: the right pedal is adjusted clockwise; the left
56 DRUMFIT INDOOR EOLO
one is adjusted counterclockwise).
2.
Insert the saddle (13) on its sliding guide (12). Tighten the knob securely.
STEP 3
Insert the handlebar (3) on its stem (4) (Fig. 4).
1.
Connect the cable in the stem to the handlebar cable. Then, fix the handlebar (3) to the
stem (4) with 4 Allen bolts (17).
2.
Attach the device holder (2) to the handlebar.
STEP 4. Fit and plug in the bike
1.
Check that all parts are correctly assembled and fixed. If they are, the assembly is finished.
2.
To train comfortably and safely, the bike must be completely stable. So, if you notice that
the bike wobbles during use, adjust the front and rear stabilisers feet (8 and 9).
Before plugging in the bicycle, read the specifications of the power adapter. Once you have
done so, place one end of the adapter into the hole provided at the front of the main frame.
The bike is now ready for use.
4. OPERATION
Getting on and off the bicycle
- Before getting on the bicycle, make sure the pedals are properly fixed. Stand next to the
bike and pass the leg that is closer to it over the frame to sit on the saddle; then, insert your
feet in the pedals.
- To get off the exercise bike, do the previous step in reverse order.
Adjusting the resistance
The pedalling resistance can be adjusted with the console built into the handlebar. Read the
console operation to adjust it.
Assembling the saddle
- To adjust the height of the saddle, remember that the correct position is the one in which
your waist is not tilted to the side when the pedal is in the lower position and the foot is
perfectly inserted in the toe clips.
- Adjust the saddle properly to ensure maximum efficiency and comfort during exercise. The
saddle is in the correct position if the user has a slightly bent knee when one of the pedals
is at a 90-degree angle relative to the ground.
- To adjust the saddle height, simply loosen the L-shaped adjustment knob (5), raise, or
ENGLISH
DRUMFIT INDOOR EOLO 57