cecotec DRUMFIT INDOOR EOLO Manual De Instrucciones página 31

ENGLISH
to chose the desired programme. You can vary the resistance level once the programme
is selected. Simply turn the display knob to the right or left while in the LEVEL function.
2.
Press the button to set the different targets (TIME-DISTANCE-CALORIE-PULSE). Press the
button to enter the target. Turn it to increase or decrease the value, then, press the button
again to confirm the setting. While exercising, the values of these four functions will be
displayed every 6 seconds. Press the button to select the function you wish to view at
any time.
3.
When you start training, the STOP indicator light will switch off and the START indicator
light will switch on.
Wake-up function
If, after 4 minutes, the console has not received any signal nor the button has been pressed, it
will go into sleep mode (the display will be switched off). Press the button to switch it back on.
Error codes
E1 (ERROR 1):
If you are training, but the console does not receive any data from the training for 4 seconds,
the error code E1 will be displayed.
E2 (ERROR 2):
When the console has problems reading the data saved in the memory, the error code E2 will
appear on the display as soon as the console is switched on.
E3 (ERROR 3):
If you are training and the bike has not exited STOP mode after 4 seconds, the error code E3
will appear on the display.
PROGRAMMES:
- The bike has the following programmes (Fig. 8)
- P1: Manual. This is the default programme, with no programmed resistance changes. The
user can choose between any resistance level.
- P2: Steps. It simulates a staggered ascent.
- P3: Hill. It simulates climbing a mountain slope.
- P4: Rolling. Reproduces a normal route with climbs and descents by adjusting the
resistance automatically.
- P5: Valley. It simulates the course of a valley (downhill and then uphill).
- P6: Fat Burn. Adjust your training so that the intensity is just right for targeted fat loss
training.
- P7: Ramp. Training that reproduces the prolonged ascent prior to a slight descent.
- P8: Mountain. Simulates the ascent and descent of a mountain slope.
- P9: Intervals. It reproduces an interval training: it alternates between high and low
60 DRUMFIT INDOOR EOLO
intensity training.
- P10: Random. Modification of the resistance in a random way.
- P11: Plateau. Simulates the route of a plateau or high plateau.
- P12: Fartlek. It reproduces Fartlek training, which combines times at a higher intensity with
times at a lower intensity.
- P13: Precipice. Simulates an intense climb with an intense descent.
- P14: Watt Control. It is a programme in which you can enter the power target to be
developed in training.
A table detailing the resistance data for each programme is inserted below:
Programme Initial resistance
P1 L9
P2 L1
P3 L9
P4 L9
P5 L17
P6 L1
P7 L5
P8 L5
P9 L5
P10 L5
P11 L5
P12 L1
P13 L1
P14 /
Using the device holder
- Pull up the top edge of the bracket, then place the mobile phone or tablet in the bracket.
- Then, release the upper edge of the bracket. Fig. 9
- Duting training, you can rotate the bracket to the left or to the right to get a better view of
ENGLISH
What is adjustable? Setting range
Level L1-L32
Level L1-L16
Level L1-L24
Level L1-L24
Level L17-L32
Level L1-L20
Level L1-L16
Level L1-L16
Level L1-L20
Level L1-L12
Level L1-L16
Level L1-L4
Level L1-L4
Watts 50-240 W
DRUMFIT INDOOR EOLO 61