Gardena EasyCut 420/45 Instrucciones De Empleo página 9

Before use, examine cable for damage, replace it if there are signs of damage
or ageing.
If the replacement of the supply cord is necessary, this has to be done by the
manufacturer or his agent in order to avoid a safety hazard.
Do not use the product if the electric cables are d amaged or worn.
Immediately disconnect from the mains electricity supply if the cable is cut, or the
insulation is damaged. Do not touch the electric cable until the electrical supply
has been disconnected.
Your electric cable must be untangled, tangled cables can overheat and reduce
the efficiency of your product.
Always disconnect the mains cable before d isconnecting any plug, cable con-
nector or extension cable.
Switch off, remove plug from mains and examine electric supply cable for
d amage or ageing before winding cable for storage. Do not repair a damaged
cable, send the product to the next GARDENA service Center or dealer author-
ised by GARDENA.
Always wind cable carefully, avoiding kinking.
Use only on AC mains supply voltage shown on the product rating label.
Under no circumstances should an earth be connected to any part of the
product.
If the product starts unintentionally when the mains plug is connected, discon-
nect the mains at once. Contact Gardena Service to check the product.
DANGER! This product makes an electromagnetic field while it operates. This
field may under some conditions interfere with active or passive medical implants.
To decrease the risk of conditions that can possibly injure or kill, we recommend
persons with medical implants to speak with their physician and the medical
implant manufacturer before you operate the product.
Cables
Use only permitted extension cables as per HD 516.
v Ask your electrical specialist.
Personal safety
Always wear suitable clothing, protective gloves, and stout shoes.
Avoid contact to the oil of the blade in particular when you react allergic with it.
Thoroughly inspect the area where the product is to be used and remove all
wires and other foreign objects.
Always hold the product properly with both hands and both handles.
Before using the product and after any impact, check for signs of wear or dam-
age and repair as necessary.
Never attempt to use an incomplete product or one with an unauthorised modifi-
cation.
Power tool use and care
Know how to stop the product quickly in an e mergency.
Never hold the product by the guard.
Do not use the product if the protection equipments (protection cover, quick
blade-stop) are damaged.
Do not use ladders whilst operating the product.
Disconnect the mains cable:
– b efore leaving the product unattended for any period;
– b efore clearing a blockage;
– b efore checking, cleaning or working on the appliance;
– i f you hit an object. Do not use your product until you are sure that the entire
product is in a safe o perating condition;
– if the product starts to vibrate abnormally. Check immediately. Excessive
v ibration can cause injury.
– before passing to another person.
Only use the product between 0 – 40 °C.
Maintenance and storage
RISK OF INJURY!
Do not touch blades.
v When finishing or interrupting work push up protection cover.
Keep all nuts, bolts and screws secure to be sure the product is in safe working
condition.
If the product got hot during operation, let it cool down before storage.
2. OPERATION
DANGER! Risk of injury!
Cut injury when the product starts accidentally.
v Before you connect or transport the product, disconnect the
mains cable and slide the protective cover
[ Fig. O1 ].
GAR_09830-20.960.06_2024-05-08.indd 9 GAR_09830-20.960.06_2024-05-08.indd 9
To connect the hedge trimmer [ Fig. O2 ]:
v Before you operate the product insert the extension cable
into the cable lock
v Never take hold of the protective cover
product.
1. Loop the extension cable
and pull tight.
2. Connect the plug
cable
3. Connect the extension cable
Work positions:
The product can be operated in 3 positions.
• Side trimming [ Fig. O3 ]
• High trimming [ Fig. O4 ]
• Low trimming [ Fig. O5 ]
To start the hedge trimmer [ Fig. O6 ]:
v Do not bypass the safety devices or switches. For example do
not attach the start buttons
To start:
The product is fitted with a two-handed safety device (2 start buttons)
to prevent the product from being turned on by accident.
1. Remove the protective cover
2. Hold the guide handle
3. Hold the main handle
button
To stop:
1. R elease the two start buttons
2. Slide the protective cover
3. MAINTENANCE
v Before you maintain the product, make sure that the mains
cable is disconnected and the protective cover
the blade
To clean the hedge trimmer [ Fig. M1 ]:
v Do not clean the product with water or with a water jet
(in particular high-pressure water jet).
1. C lean the product with a damp cloth.
2. C lean the airflow slots with a soft brush (do not use a screwdriver).
3. Lubricate the blade
Art. 2366). Avoid contact with the plastic parts.
4. STORAGE
To put into storage [ Fig. S1 ]:
The product must be stored away from children.
1. Disconnect the mains cable.
2. Clean the product (see 3. MAINTENANCE) and slide the protective
1 over the blade 2
cover
3. S towe the product in a dry area where it has protection from frost.
DANGER! Electric shock!
To avoid damage to the mains cable
cable 4 must be inserted into the cable lock
5 .
4 , insert the loop into the cable lock
6 of the product into the socket
4 .
4 into a 230 V mains socket.
DANGER! Risk of injury!
Risk of injury if the product does not stop when you
release the start button.
9 / q to the handle.
1
from the blade
8 with one hand and push the start button
0
with the other hand and push the start
q . The product will start.
9 / q .
1
over the blade
DANGER! Risk of injury!
Cut injury when the product starts accidentally.
2 .
DANGER! Electric shock!
Risk of injury and risk of damage to property.
2 with a low viscosity oil (e. g. GARDENA spray-oil
1 2
over the blade .
3 the extension
5 .
4
1 when connecting the
5
7 of the extension
2
.
9 .
2
.
1 is slid over
9
08.05.24 10:54 08.05.24 10:54