Built-In Grundfos Sensor - Grundfos TPE2 D Manual Del Usuario

Settings
"Operating range"
"Ramps"
"Pump number"
"Radio communication"
"Analog input 1"
"Analog input 2"
"Analog input 3"

"Built-in Grundfos sensor"

"Pt100/1000 input 1"
"Pt100/1000 input 2"
"Digital input 1"
"Digital input 2"
"Digital in/output 3"
"Digital in/output 4"
"Predefined setpoint"
"Analog output"
"External setpoint funct."
"Signal relay 1"
"Signal relay 2"
"Limit 1 exceeded"
"Limit 2 exceeded"
"Alternating operation, time"
"Time for pump changeover"
"Standstill heating"
"Motor bearing monitoring"
"Service"
"Store settings"
"Recall settings"
"Undo"
"Pump name"
"Connection code"
"Unit configuration"
* Only available if Grundfos GO is connected to a multipump system.
Alarms and warnings
"Alarm log"
"Warning log"
"Reset alarm" button
Assist
"Assisted pump setup"
"Assisted fault advice"
"Multipump setup"
30
TPE3, TPE3 D TPE3, TPE3 D
● ●
● ●
● ●
● ●
● ●
● ●
● ●
● -
● ●
● ●
● ●
● ●
● ●
● ●
● ●
● ●
● ●
● ●
● ●
● ●
● ●
- -
- -
● ●
● ●
● ●
● ●
● ●
● ●
● ●
● ●
● ●
TPE3, TPE3 TPE2, TPE2
D D
● ●
● ●
● ●
TPE3, TPE3 TPE2, TPE2
D D
● ●
● ●
● ●
Multipump
Section
system
● 17.19 Operating range
17.25 "Ramps"
- 17.30 "Number" (Pump number)
17.31 "Radio communication"
-
(Enable/disable radio comm.)
-
- 17.10 Analog inputs
-
● 17.11 Built-in Grundfos sensor
-
17.12 Pt100/1000 inputs
-
-
17.13 Digital inputs
-
-
17.14 Digital inputs/outputs
-
● 17.21 "Predefined setpoints"
- 17.17 Analog output
- 17.20 External setpoint function
-
17.16 "Signal relay 1 and 2" (Relay
outputs)
-
●
17.23 Limit-exceeded function
●
●*
17.51 "Multipump setup" (Setup of
multi-pump system)
●*
- 17.26 "Standstill heating"
- 17.28 Motor bearing monitoring
- 17.29 "Service"
17.39 "Store settings" (Store actual
-
settings)
17.40 "Recall settings" (Recall stored
-
settings)
● 17.41 "Undo"
● 17.42 "Pump name"
● 17.43 "Connection code"
● 17.34 "Unit configuration" (Units)
Multipump
Section
system
● 17.45 Alarm log
● 17.46 Warning log
●
Multipump
Section
system
17.48 Assisted pump setup
● 17.53 Assisted fault advice
17.51 "Multipump setup" (Setup of
●
multi-pump system)
Page
45
49
50
50
38
39
40
40
41
47
43
45
42
48
53
49
49
50
51
51
51
51
51
50
Page
52
52
Page
52
56
53