Program Change; Song Select; System Reset - Yamaha LS9 Serie Manual De Instrucciones

1.4 PROGRAM CHANGE

Reception
If [PROGRAM CHANGE ECHO] is ON, bank select messages will also be echoed
from MIDI OUT.
If SINGLE CH is selected, these messages are received if [PROGRAM CHANGE Rx] is
ON and the [Rx CH] matches. However if [OMNI] is ON, these messages are received
regardless of the channel. When these messages are received, scene memory and effect
library are recalled according to the settings of the [PROGRAM CHANGE EVENT
LIST].
Transmission
If [PROGRAM CHANGE Tx] is ON, these messages are transmitted according to the
[PROGRAM CHANGE Table] settings when scene memory and effect library are
recalled.
If SINGLE CH is selected, these messages are transmitted on the [Tx CH] channel.
If the recalled scene memory and effect library has been assigned to more than one
PROGRAM NUMBER, the lowest-numbered PROGRAM NUMBER for each MIDI
channel will be transmitted.
PROGRAM CHANGE messages are not used for transmission to
there is no guarantee that the contents of the assignment tables will match.
(PARAMETER CHANGE messages are always used.)
You can choose either MULTI MIDI CH or SINGLE CH.
If SINGLE is selected
You can choose the Rx CH, OMNI CH, and Tx CH.
You can choose whether a bank select message will be added.
A bank of up to 16 can be specified.
If MULTI is selected
The Rx and Tx channels will be the same.
The assignment table will use the settings for each MIDI channel. Bank select messages
will not be added.
You can make settings for up to sixteen MIDI channels.
Program change
STATUS 1100nnnn Cn
Program number (0-127)
DATA 0nnnnnnn nn
2 SYSTEM REALTIME MESSAGE

2.1 SONG SELECT

Select the track number shown in the TITLE LIST screen of the USB memory recorder.
Song select
STATUS 11110011 F3
Song number (0-127)
Song number 0sssssss ss
2.2 TIMING CLOCK
Reception
This message is used to control effects. This message is transmitted twenty-four times
per quarter note.
Echoing of this message depends on the OTHER item in the ECHO settings.
Timing clock
STATUS 11111000 F8
2.3 ACTIVE SENSING
Reception
Once this message has been received, MIDI communication will be initialized (e.g.,
Running Status will be cleared) if no message is received for an interval of 400 ms.
This message is not subject to echoing.
Active sensing
STATUS 11111110 FE

2.4 SYSTEM RESET

Reception
When this message is received, MIDI communication will be initialized (e.g., Running
Status will be cleared).
This message is not subject to echoing.
System reset
STATUS 11111111 FF
(Cn) 3 SYSTEM EXCLUSIVE MESSAGE
3.1 MMC
< MMC STOP >
Reception
If the [DEVICE NO.] matches or is 7F, receives this message and stops.
STATUS
ID No.
Device ID
COMMAND
EOX
< MMC PLAY >
LS9
Editor because
Reception
If the [DEVICE NO.] matches or is 7F, receives this message and starts playback.
STATUS
ID No.
Device ID
COMMAND
EOX
< MMC DEFERED PLAY >
Reception
If the [DEVICE NO.] matches or is 7F, receives this message and starts playback.
STATUS
ID No.
Device ID
COMMAND
(F3)
EOX
< MMC RECORD STROBE >
Reception
If the [DEVICE NO.] matches or is 7F, receives this message, and if stopped, starts
recording.
(F8)
STATUS
ID No.
Device ID
COMMAND
EOX
(FE)
< MMC PAUSE >
Reception
If the [DEVICE NO.] matches or is 7F, receives this message, and if playing, pauses.
STATUS
ID No.
Device ID
(FF)
COMMAND
EOX
Formato de datos MIDI
System exclusive message
11110000 F0
Real time System exclusive
01111111 7F
Destination (00-7E, 7F:all call)
0ddddddd dd
Machine Control Command(MCC) sub-id
00000110 06
Stop(MCS)
00000001 01
End of exclusive
11110111 F7
System exclusive message
11110000 F0
Real time System exclusive
01111111 7F
Destination (00-7E, 7F:all call)
0ddddddd dd
Machine Control Command(MCC) sub-id
00000110 06
Play(MCS)
00000010 02
End of exclusive
11110111 F7
System exclusive message
11110000 F0
Real time System exclusive
01111111 7F
Destination (00-7E, 7F:all call)
0ddddddd dd
Machine Control Command(MCC) sub-id
00000110 06
Deferred Play(MCS)
00000011 03
End of exclusive
11110111 F7
System exclusive message
11110000 F0
Real time System exclusive
01111111 7F
Destination (00-7E, 7F:all call)
0ddddddd dd
Machine Control Command(MCC) sub-id
00000110 06
Record strobe
00000110 06
End of exclusive
11110111 F7
System exclusive message
11110000 F0
Real time System exclusive
01111111 7F
Destination (00-7E, 7F:all call)
0ddddddd dd
Machine Control Command(MCC) sub-id
00000110 06
Pause(MCS)
00001001 09
End of exclusive
11110111 F7
LS9-16/32 Manual de instrucciones
261