Panasonic GP-UH532C Manual De Instrucciones página 28

The description below explains how to operate the ADVANCED MENU basically.
ADVANCED MENU top page
EXPOSURE page
PF LABEL: •••••••••••••••• ID: PANA_DEFAULT
1
AE * AUTO
SHUTTER AUTO
BINNING OFF
GAIN * AUTO
LONG EXPOSURE OFF
AREA SELECTION ALL
PEAK/AVE LEVEL 8 [ 0 * 8 ]
HEAD GAIN OFF
[ EXPOSURE PICTURE CONTRAST PROFILE FUNC SYSTEM HEAD
PROFILE page
PF LABEL: •••••••••••••••• ID: PANA_DEFAULT
1
USER PROFILE
USER PROFILE ID * OFF
USER PROFILE LABEL * OFF
FLUORESCENCE MODE OFF
[ EXPOSURE PICTURE CONTRAST PROFILE FUNC SYSTEM HEAD
HEAD page
WHITE SHADING
AUTO
H/V PHASE ADJUST H 0 [
V 0 [
[ EXPOSURE PICTURE CONTRAST PROFILE FUNC SYSTEM HEAD
Step 1
Set up each item.
• Select the item to be set
Move the cursor by turning the [RED] volume or press-
ing the [g] or [h] button.
• Change the set item
Turn the [LEVEL] volume or press the [e] or [f] button.
• Display advanced setup page
Press the [SEL] button for the item "*" is indicated.
• Return to the upper level setup page
Press the [MENU] button.
Note:
• The cursor is a blinking part.
In this document, it is indicated by " Shaded ".
Restore default
• To restore each setting in the SETUP MENU to the default, move the cursor to the item to change and hold down the [e]
and the [f] buttons simultaneously for 1 second or more.
• To restore the initial setting of all the profiles, use "USER PROFILE RESET". (☞ page 42)
• To restore the initial setting of only the selected profile, press the [PROFILE] button for more than 1 second.
• To restore the initial setting of all the items in each page of "ADVANCED MENU", move the cursor to the tab on the bottom
of the page, and hold down the [e] and [f] buttons simultaneously for 1 second or more.
28
PICTURE page
PF
1
LEVEL 32 [ 0 63 ] WHITE BAL MODE
*
---
DETAIL BAND
LEVEL dB [ 3 12 ] DNR LEVEL
12 *
--- PEDESTAL LEVEL
FLARE COMP
COLOR LEVEL
COLOR MATRIX
] [ EXPOSURE PICTURE CONTRAST PROFILE FUNC SYSTEM HEAD
FUNC page
FLIP AND MIRROR
F+M STATUS DISPLAY
COLOR BAR
FOOTSW CONTROL CH1
FOOTSW CONTROL CH2
USER PROFILE SAVE/LOAD
SAVE/LOAD MODE
DIGITAL ZOOM
DIGITAL ZOOM STATUS DISPLAY OFF
] [ EXPOSURE PICTURE CONTRAST PROFILE FUNC SYSTEM HEAD
( )
SET
- 20 ]
20 *
- 11 ]
11 *
]
LABEL: •••••••••••••••• ID: PANA_DEFAULT
* AWC R -GAIN 128 [ 0 255 ]
*
B -GAIN 128 [ 0 * 255 ]
* SOFT LEVEL 16 [ 0 31 ]
*
5 [ 0 10 ]
*
76 [ 68 95 ]
*
OFF
160 [ 0 * 255 ]
* USER
]
OFF
OFF
* ON
PROFILE1 ←→ 2
FREEZE
* USB → CAMERA ( ALL )
( USB ) AUTO
ON
]
Step 2
Press the [MENU] button for 1 second or more after saving
the setup content to close the setup page and return to the
camera image.
The setup content will be maintained even after the power
of the CCU is turned off.
CONTRAST page
PF LABEL: •••••••••••••••• ID: PANA_DEFAULT
1
GAMMA SELECT S-CURVE
GAMMA VALUE 0.45 [ 0.35 * 0.55 ]
KNEE MODE MANUAL
KNEE POINT 8 [ 0 15 ]
*
KNEE SLOPE 3 [ 0 7 ]
*
IE FUNCTION SELECT WDR
LEVEL 80 [ 0 255 ]
*
[ EXPOSURE PICTURE CONTRAST PROFILE FUNC SYSTEM HEAD
SYSTEM page
DISPLAY RANGE(FHD) FULL
OSD POSITION UPPER LEFT
HDMI1 COLOR DEPTH YPbPr ( 420 ) 8 BIT
HDMI2 COLOR DEPTH YPbPr ( 422 )
G/L SYNC TERMINAL SETTING OUT
G / L SYNC STATUS INFO INTERNAL
D MODE OFF
3
* TIME ADJUSTMENT
* USER PROFILE RESET
[ EXPOSURE PICTURE CONTRAST PROFILE FUNC SYSTEM HEAD
]
]