Publicidad
Idiomas disponibles
Idiomas disponibles
2. Setting the OFF time (1 :30 PM)
Turn the TIMER switch OFF.
Turn the FUNCTION switch OFF.
a. Set the clock to 0:00 by pressing the HOUR and
MINUTE switches simultaneously.
b. Set the hour digits to "1 :00 PM" by the HOUR switch.
c. Set the minute digits to "30" by the MINUTE switch.
The timer is now ready to turn ON and OFF automatically.
Turn the Tl M ER switch ON and the R-1000 will turn ON at
11: 15 AM and turn OFF at 1 :30 PM every day.
FUNCTION
TIME SET
FREQUENCV
01
HOUR
TIMER SET
POWER
fll
_.._ON
r'l
LJ
.A.oFF
LJOFF
FUNCTION
FREQUENCV
~
\JT
TIMER SET
POWER
TIME SET
HOUR
TIMER
FUNCTION
TIME SET
FREQUENCV
@
I
CLOCK
1
HOUR
TIMER SET
POWER
TIMER
~
---oN
CJOFF
.A.OFF
.J
ON
nnn
l-.1.LI
!_/
1
L_CLOCK__)
L_FREQUENCV
~
AMC]ON
PMCJ
Turn the FUNCTION switch
OFF.
Depress the HOUR
a nd
M 1 NUTE
switches
simultaneously.
The clock indicates 0:00.
111n
/.!-f
!_/
1
L_CLOCK__)
L_FREQUENCY
~
AMCJ
PMCJON
Set the hour digits to "1 ".
~~~f_._~~L~/~l=~o•
1
L_CLOCK__)
L_FREQUENCV
~
Set the minute digits to
"30".
Next, turn the TIMER switch
ON .
Fig. 3-8 Setting the OFF Time (1 :30 PM)
NOT ES:
1. When the ON time is set behind the actual time (for ex-
ample. 11:30 AM). the R-1000 will not turn on until
11 : 15 AM the following day.
2.
The timer will not turn off automatically unless ON-time
is set. To use it as a sleep timer. set ON-time so that the
R-1000 is operated after 1 minute or so, then set OFF-
time.
3. Once the TIMER switch is set to ON, the timer turns ON
and OFF every day at the designated time. (The TIMER
switch can not be effective if the FUNCTION switch is
set to FREQUENCY position.)
4. With the TIMER switch in the ON position. the timer
keeps operating regardless of the position of the POWER
switch.
5. When setting the ON and OFF time be sure to change the
position of the FUNCTION switch.
3.8 UNATTENDED RECORDING ON TAPE
The timer function feature also allows you to record a
desired broadcast on tape even when you are away from
home. The tape recorder to be used should be provided with
the following functions:
1. Recording terminal to accept external line input signals.
2.
Automatie start/stop circuit which controls tape record
operatio.n by external input signal.
3. The tape recorder control terminals should be turned on
and oft by an external signal (starts at ON and stops at
OFF).
Connections and Settings (See page
2
Fig. 1-8)
a. Tune the R-1000 to the desired receive frequency, any
operating mode.
b. Connect the R-1000 RECORD jack to the LIN E IN of
your tape recorder (cable user supplied).
c. Set the R-1000 timer to your desired ON and OFF
time. Next. turn the TIMER switch ON.
d. Connect the external control terminal of the tape
recorder to the R-1000 REMOTE connector, pin 1
and pin
4.
e. Set the tape recorder in record mode.
The tape recorder is now ready for unattended tape recor-
ding. When the timer reaches the ON-time. the R-1000
turns on and the built-in relay is activated to operate the
tape recorder through the REMOTE connector (pins 1 and
4
are shorted). (See Fig. 3-9)
Mute Circuit
The R-1000 has a mute circuit for use in combination with a
tranceiver or transmitter.
The R-1000 RF stage will mute by grounding Pin 7 on the
remote terminal. (See Fig. 3-9)
9
Publicidad
