3M PELTOR WS LiteCom Plus MT73H7A4310WS6EU Manual Del Usuario página 15

4.4. CARRIER DEVICES
These earmuffs should be fitted to and used only with the
carrier devices listed in table K. These earmuffs were tested
in combination with the carrier devices listed in table K, and
may give different levels of protection if fitted to different
carrier devices.
Explanation of the carrier attachment table:
Table
ref.
K
Compatible carrier devices
K:1 Manufacturer
K:2
Model
K:3 Attachment code
K:4
Head size, earmuff with foam cushions:
S = small, M = medium, L = large
K:5
Head size, earmuff with gel cushions:
S = small, M = medium, L = large
5. OVERVIEW
(Figure A:A - A:C)
A:A Headband versions
A:B Neckband versions
A:C Carrier attachment versions
5.1. A) COMPONENTS
(Figure A:1 - A:24)
A:1 Headband (PVC foil, PA)
A:2 Headband wire (stainless steel)
A:3 Cushion (PVC)
A:4 Lithium-ion battery (rechargeable) (PC/ABS)
A:5 Guide incl. microphone guide (POM, TPE)
A:6 Microphone cable (PUR, TPS, SEBS)
A:7 Microphone contact (TPS, SEBS)
A:8 Speech microphone input (J22) (TPE)
A:9 Bluetooth button (PBT)
®
A:10 Speech microphone (dynamic microphone) (ABS, PA)
A:11 Foam liner (PUR foam, Polyester)
A:12 Microphone windshield for ambient listening (Polyester
foam)
A:13 External input/output (e.g. for external communication
radio, external telephone) (brass)
A:14 PTT (Push-To-Talk button) for built-in communication
radio (PBT)
A:15 [–] button (Silicone)
A:16 On/Off/Mode button (Silicone)
A:17 [+] button (Silicone)
A:18 Cup (ABS)
A:19 Headband cable (TPU, TPE)
A:20 Antenna (PU, TPU)
A:21 Carrier attachment (POM, PA66)
A:22 Carrier attachment wire (stainless steel)
A:23 Neckband cover (PO)
A:24 Neckband wire (stainless steel)
Description
* Only WS (Bluetooth
6. SETUP
6.1. REPLACING/CHARGING THE BATTERIES
(Figure 1)
Insert the rechargeable battery (ACK081) in the battery
compartment. Push down the clamp.
Low battery level is indicated by a voice message: "battery
low", repeated every five minutes. If the batteries are not
replaced a "battery empty" warning will eventually be heard.
The unit will then switch off automatically.
NOTE: Use the following battery in this product: 3M™
PELTOR™ ACK081 charged with cable 3M™ PELTOR™
AL2AI connected to a 3M™ PELTOR™ FR08 (power supply).
NOTE: Performance may deteriorate as the batteries get low.
6.2. RECHARGING BATTERIES
(Figure 1)
Turn off the headset. Insert a blunt tool under the edge of the
clamp and pull outwards/upwards. Remove the battery and
charge it separately, or leave the battery in place and charge it
in the hearing protector.
7. FITTING INSTRUCTIONS
7.1. HEADBAND
(Figure B:1 - B:3)
B:1 Slide out the cups and tilt the top of the shell out, as the
cable must be on the outside of the headband.
B:2 Adjust the height of the cups by sliding them up or down
while holding the headband in place.
B:3 The headband should be positioned across the top of the
head as shown and should support the weight of the headset.
7.2. NECKBAND
(Figure B:4 - B:6)
B:4 Place the cups in position over your ears.
B:5 Keep the cups in position, place the head strap on top of
your head and lock it tight in position.
B:6 The head strap should be positioned across the top of
your head and should support the weight of the headset.
7.3. CARRIER ATTACHMENT
(Figure B:7 - B:11)
B:7 Insert the carrier attachment in the slot on the carrier and
snap it into place (B:8).
B:9 Work mode: Press the headband wires inwards until you
hear a click on both sides. Make sure that the cups and the
headband wires do not press on the edge of the carrier when
in work mode as this could reduce the noise attenuation of
the earmuff.
B:10 Ventilation mode: To switch the unit from work mode to
ventilation mode, pull outward on the earcups until you hear a
click. Avoid placing the cups against the carrier (B:11) as this
prevents ventilation.
7.4. MICROPHONE
(Figure C:1 - C:2)
To maintain noise-cancelling performance, the speech
microphone should be positioned very close to your mouth
(3 mm).
) models
®
EN
4