3M PELTOR WS LiteCom Plus MT73H7A4310WS6EU Manual Del Usuario página 16

EN
7.5. REPLACING THE CARRIER ATTACHMENT
PLATE
(Figure E:1 - E:2)
For proper fitting on different industrial safety helmets, the
helmet attachment plate may need to be replaced. Find the
recommended attachment in table L. Other plates can be
obtained from your dealer. A screwdriver is needed.
(E:1) Loosen the screw holding the plate.
(E:2) Replace the plate, ensure the plate is turned the right way
and tighten the screw.
8. OPERATING INSTRUCTIONS
8.1. OPERATION TIME
Approximate operation time with a fully charged ACK081
battery (1800 mAh):
• WS LiteCOM Plus: Approximately 18 hours.
• LiteCom Plus: Approximately 20 hours
NOTE:
Depending on the environment, temperature, and battery, the
operation time may vary.
8.2. POWERING THE UNIT ON AND OFF
(Figure 2 and Figure A)
Press and hold the On/Off/Mode button (A:16) for 2 seconds
to switch the headset on or off. A voice message will confirm
that the unit has been switched on or off with the voice
message "power on" or "power off".
NOTE: The headset is automatically powered off after four hours
of inactivity. This is indicated by the voice message "automatic
power off".
NOTE: The last setting is always saved when the headset is
switched off.
8.3. ADJUSTING THE VOLUME LEVEL
(Figure 3)
Use the [+] and [–] buttons to adjust the volume. By default,
the [+] and [–] buttons will control the volume of the active
sound source, which could be any one of the following:
two-way radio, Bluetooth communication, or ambient
®
listening. When receiving or transmitting with the two way
radio, the [+] and [–] buttons will control the two-way radio
volume.
*If a Bluetooth device is active, the [+] and [–] buttons will
®
control the Bluetooth audio playback. In all other cases, the
®
[+] and [–] buttons will control the ambient listening volume
level. The respective volume levels can also be adjusted in
the menu.
8.4. RADIO TRANSMISSION
8.4.1. VOX (VOICE OPERATED TRANSMISSION)
(Figure 5 and figure A:14)
Enables automatic transmission when the sound level at the
microphone is above the VOX level.
To turn VOX on or off, short press ~0.5 seconds the PTT
button (A:14) (Figure 5) two times.
8.4.2. PTT (PUSH-TO-TALK TRANSMISSION)
(Figure 5, figure A:14 and figure A:16)
Press and hold the PTT button (A:14) to transmit manually
5
using the radio. When the radio is transmitting or receiving,
the button (A:16) will flash rapidly. PTT transmission works at
all times, regardless of the BCLO and settings.
NOTE: In order to receive transmission, the channel must not
be blocked by transmission via PTT or VOX.
8.4.3. COMMUNICATION FACE TO FACE, PTL
(PUSH-TO-LISTEN)
(Figure 6 and figure A:16)
The Push-To-Listen feature enables you to instantly listen to
your environment by muting the Bluetooth
activating the level-dependent microphones. Short press
(~0.5 seconds) the power button (A:16) two times to activate
Push-To-Listen. Short press any button to deactivate
Push-To-Listen.
8.5. *BLUETOOTH
8.5.1. *BLUETOOTH
Bluetooth is the name of a technical standard for short-range
®
wireless transmission, with a working range of approximately
10 meters. This headset can be used with other Bluetooth
enabled units that support any of the profiles: headset (HSP),
hands-free (HFP), or streaming audio (A2DP).
If the message "no paired devices" is heard, no Bluetooth
device is linked to the headset.
If the message "connecting Bluetooth
a Bluetooth
connected.
If the message "connecting Bluetooth
heard, a Bluetooth
connected.
8.5.2. *BLUETOOTH
The WS models support Bluetooth
Use Bluetooth
to two Bluetooth
the type of Bluetooth
activities, the headset controls the Bluetooth
different ways. The headset prioritizes and coordinates
activities from the connected Bluetooth
NOTE: The default setting is Bluetooth
to activate Bluetooth
headset.
8.5.3. *PAIRING A BLUETOOTH
(Figure 4, figure 7 and figure A)
The first time the headset is powered on or after reset to
factory default, pairing mode is entered by pressing the
Bluetooth button (Figure 4). A voice message confirms,
®
"Bluetooth
®
You can also start *Bluetooth
holding (10 seconds) the On/Off/Mode button (A:16) when in
off mode. A voice message confirms, "power on, battery
status, Bluetooth
Pairing mode can also be entered from the Sub-menu (Figure
11). See "configuring your headset". This could be used for
pairing a second device.
Make sure that Bluetooth
your Bluetooth
* Only WS (Bluetooth ) models
®
OPERATION
®
FUNCTION
®
, connected" is heard,
®
-enabled device is linked to the headset and
®
, connection failed" is
®
device is linked to the headset, but not
®
MULTIPOINT TECHNOLOGY
®
Multipoint technology.
®
Multipoint technology to connect your headset
®
devices at the same time. Depending on
®
devices connected and their current
®
devices
®
Multipoint, you have
®
single in the set-up mode of the
®
DEVICE
®
pairing on".
pairing by long pressing and
®
pairing on".
®
communication is activated on
®
device. Search and select "WS LiteCom Plus"
®
audio volume and
®
-
®
®
devices in
®