Maintenance And Storage - Honda HF2317 Manual De Instrucciones

11) Pay maximum attention when working in reverse gear. Look
behind you to make sure there are no obstacles before and during
operations in reverse gear.
12) Use care when pulling loads or using heavy equipment:
– Use approved drawbar hitch points only when towing.
– Limit loads to those you can safely control.
– Do not turn sharply. Take care when reversing;
– Use counterweight(s) or wheel weights whenever advised in the
instructions manual.
13) Disengage the cutting means or the power socket when crossing
areas with no grass, when moving to or from areas that require mow-
ing, and move the cutting-means assembly to its highest position.
14) Pay attention to traffic when using the machine near roads.
15) WARNING! The machine has not been approved for use on
public roads. It must be used (as indicated by the highway code) in
private areas closed to traffic.
16) Never operate the machine with damaged, missing or incorrectly
assembled guards (grass catcher, rear discharge guards).
17) Always keep hands and feet away from the cutting means, when
starting and when using the machine. Attention: the cutting means
will continue to rotate for a few seconds after disengagement or after
you have switched off the engine. Keep away from the discharge
opening.
18) Do not leave the machine stationary on high grass with the en-
gine running to avoid the risk of starting a fire.
19) When using the attachments, never direct the opening towards
people.
20) Use manufacturer-recommended attachments only.
21) Don't use the machine if the attachments/tools are not installed
in their seats.
22) Pay attention when using the grass catcher and attachments that
can alter the stability of the machine, especially on slopes.
23) Do not change the engine settings or over-rev the engine.
24) Do not touch the engine parts as they get very hot when running.
Burns hazard.
25) Disengage the cutting means or power socket, put in neutral and
engage the parking brake, turn off the engine and remove the ignition
key (checking that all moving parts are completely stationary):
– Whenever the machine is left unattended or the operator dis-
mounts from the driving seat:
– Before clearing blockages or unclogging the discharge chute;
– Before checking, cleaning or working on the machine;
– After striking a foreign object. Inspect the machine for damage and
make repairs before using it again.
26) Disengage the cutting means or the power socket and switch off
the engine (making sure that all moving parts are stationary):
– Before refuelling;
– Whenever you remove or reattach the grass catcher;
– Whenever you remove or reattach the discharge guard;
– Before adjusting the cutting height, if this operation can not be
performed from the driving seat.
27) Disengage the cutting means or the power socket during trans-
port and whenever it is not in use.
28) Reduce the throttle setting before stopping the engine. Shut off
the fuel supply on completing the work, following the instructions in
the engine manual.
29) Pay attention to cutting means assemblies with more than one
cutting means, as a rotating cutting means can trigger the rotation
of the others.
30) Never disengage, deactivate, remove or tamper with the safety
systems/micro switches installed.
31) WARNING – If something breaks or an accident occurs whilst
working, turn off the engine immediately and move the machine away
to prevent further damage; if an accident occurs with injuries or third
parties are injured, carry out the first aid measures most suitable
for the situation immediately and contact the medical authorities for
any necessary health care. Carefully remove any debris which could
cause damage or injury to persons or animals if ignored.
32) WARNING – The noise and vibration levels shown in these in-
structions are the maximum levels for use of the machine. The use
of an unbalanced cutting means, excessive speed of movement, or
lack of maintenance have a significant influence on noise emissions
and vibrations. Consequently, it is necessary to take preventive steps
to eliminate possible damage due to high levels of noise and stress
from vibration. Maintain the machine well, wear ear protection de-
vices, and take breaks while working.
33) Do not use USB accessories while cutting grass or driving.
D) MAINTENANCE AND STORAGE
1) WARNING! – Before cleaning or doing maintenance work, take
out the ignition key and read the relevant instructions. Wear proper
clothing and protective gloves whenever your hands are at risk.
2) WARNING! – Never use the machine with worn or damaged parts.
Faulty or worn-out parts must always be replaced and never repaired.
Use original replacement parts only: the use of non-original and/or
incorrectly fitted parts will jeopardize the safety of the machine, may
cause accidents or personal injuries for which the Manufacturer is
under no circumstance liable or responsible.
3) Any adjustments or maintenance operations not described in this
manual must be carried out by your Dealer or a specialized Service
Centre with the necessary knowledge and equipment to ensure
that the work is done correctly maintaining the machine's original
safety level. Any operations performed in unauthorized centres or by
unqualified persons will totally invalidate the Warranty and all obliga-
tions and responsibilities of the Manufacturer.
4) After each use, remove the ignition key and check for damage.
5) Keep all nuts, bolts and screws tight to be sure the equipment is in
safe working condition. Routine maintenance is essential for safety
and for maintaining a high performance level.
6) Check that the cutting means screws are properly tightened on a
regular basis.
7) Wear work gloves when handling, disassembling and reassem-
bling all cutting means.
8) Keep the cutting means well balanced during sharpening. All work
on the cutting means (disassembly, sharpening, balancing, reas-
sembly and/or replacing) are demanding jobs that require special
skills as well as special tools. For safety reasons, these jobs are best
carried out at a specialised centre.
9) Check that the brakes work properly on a regular basis. It is vital
for brakes to undergo regular maintenance and, where necessary,
repair work.
10) Check the side discharge guard, the discharge guard, the grass
catcher and the intake grille frequently. Replace them if they are
damaged.
11) Replace any instruction or warning message stickers, if dam-
aged.
12) When the machine is to be stored or left unattended, lower the
cutting-means assembly.
13) Store the machine out of the reach of children.
14) Do not store the machine with fuel in the tank in an area where
the fuel vapours could reach an open flame, a spark or a strong heat
source.
15) Allow the engine to cool down before storing in any enclosure.
16) To reduce fire hazards, keep the engine, silencer, battery com-
partment and petrol storage area free of grass, leaves, or excessive
grease. Always empty the grass catcher and do not leave containers
full of cut grass inside storage areas.
17) To reduce fire hazards, check there are no oil and/or fuel leaks
on a regular basis.
18) If the fuel tank has to be emptied, this should be done outdoors
once the engine has cooled down.
19) Never leave the keys in the ignition or within reach of children or
unauthorised persons. Always remove the ignition key before doing
any maintenance.
20) Be careful during adjustment of the machine to prevent entrap-
ment of the fingers between moving parts of the cutting means and
fixed parts of the machine.
E) TRANSPORT
3 EN