Transport And Handling; Disposal/Dismantling; Installation And Commissioning; Warnings And Precautions - Zhermack CYCLOPE Manual Del Usuario

• It is recommended that you keep the original
packaging (see paragraph 5.3).
• The customer is responsible for ensuring that
the product delivered to the manufacturer
is properly packaged. The manufacturer is
not liable for any defects, malfunctions or
damage to the product due to the use of
packaging that is not suitable or of the same
or higher quality than that used for the
original delivery.
5.3

TRANSPORT AND HANDLING

If the equipment must be moved:
• disconnect the equipment from the electric point;
• hold the equipment, always keeping it in a vertical
position. Regarding this, pay attention to the weight
and clearance of the equipment (see par. 4.2.2), in order
to prevent any type of damage occurring due to the
failure of considering these values;
• pack the equipment in the original packaging. If this is
not possible, take all necessary precautions to protect
the equipment from knocks and drops, as the goods are
transported at the owner's risk.
• Failure to comply with the rules stated above
relieve the Manufacturer from any liability
regarding equipment malfunctioning
consequently makes the warranty null and
void.
• When shipping
equipment to an Authorised After-Sales
Centre always enclose a copy of the purchase
document and a copy of the properly filled-in
identification form.
Before transporting the device, make sure the
safety knobs are in place and tightly fixed. Use the
original packaging. Failure to respect these
precautions could result in damage to the device.
5.4 DISPOSAL / DISMANTLING
When disposing of the packaging material the user must
follow the regulations in force in the country of use
relative to the following materials:
• wood/paper: non-polluting materials, but must be
re-cycled correctly;
• polystyrene/plastic: pollutant material, do not burn
(toxic fumes) or dispose of in the environment. Dispose
of these materials in compliance with the regulations in
force in the country of use.
If the equipment is to be dismantled, the operator must
be in charge of dismantling, elimination and re-cycling
of the following materials in compliance with the EEC
Directives and the laws in force in the country of use:
• plastic parts; steel parts; glass parts; insulated electric
cables; rubber parts.
• there are no toxic or corrosive substances.
cyclope
and
and/or delivering the
The reference figures can be found on pages 3 and 4 of this manual.
The device must not be disposed of as urban
waste. At the end of its working life, it must be
taken to a waste separation and recycling
centre in compliance with European Directive
no. 2012/19/UE or in accordance with the
legislation in force in the country of sale.
CHAPTER 6: INSTALLATION AND COMMISSIONING
6.1

WARNINGS AND PRECAUTIONS

Before carrying out installation, make sure that all safety
conditions exist and follow the indications given below
carefully.
6.2

ACCEPTED ENVIRONMENTAL CONDITIONS

Unless stated otherwise, at the time of ordering, it
is intended that the equipment must be envisioned
to function regularly in the following environmental
conditions:
Place of Use
Altitude
Working temperature
Humidity
Conditions different to those prescribed can cause
anomalies or sudden breakdown. Lighting in the
installation area of the equipment must be sufficient to
guarantee good visibility in all points of the equipment.
Luminosity not less than 200 lux must be guaranteed. The
lighting must be uniform without reflections, which could
dazzle the operator.
The equipment itself cannot cause explosions or
fire: the equipment is not prepared and/or
designed to operate in environments with
explosive atmosphere or with the risk of fire.
The working area lighting plant is an important
factor for the safety of persons and the quality of
work. In Italy this subject is governed by a
Ministerial Decree that clearly determines the
average level of prescribed lighting. In other
countries the regulations in force are valid
regarding accident-prevention and hygiene in
the workplace.
6.3

SPACE NECESSARY FOR USE

The choice of the place and space required for installation
is an important factor for the quality of work and safety
and for correct maintenance activities. This area must not
only be spacious enough to allow for optimum equipment
operation - also during cleaning and maintenance phases
- but must also be well lit, aired, not dusty and not
exposed to direct sunlight.

6.3.1 WORKTOP

Fig. D: cyclope has been designed to work on a rigid
worktop and parallel to the ground. Suitable worktops
include service furniture (operator is standing) or
EN
Indoors
Up to 2000 m
From 10°C to 35°C
Max 80%
19