Start-Up; Declared Use; Non-Declared And Prohibited Use; Using The Equipment - Zhermack CYCLOPE Manual Del Usuario

modelling tables (operator is sitting). All worktops must
be checked for stability. Note also that the unit must
be positioned so the connection plug can be handled/
manipulated with ease.
6.4 CONNECTION TO ENERGY SOURCES
The connection is made using the power supply cable.
Check:
• that mains power supply voltage and frequency
correspond to those indicated on the identification
plate (an incorrect power supply voltage may damage
EN the equipment);
• that the power supply mains has a suitable earth
connection.
Do not tamper with the power supply cable and
relative plug. For replacement of the same due
to damage and/or wear, only contact Authorised
After-Sales Centres.
An earth connection is mandatory. If an
extension must be used temporarily, it
must be in compliance with the
standards in force in the country of use.
6.5 INITIAL START UP
Fig. 1: Rest the appliance on a level work surface with
the induction chamber facing the operator.
Fig. 2: Insert the main power socket into the appropriate
outlet at the rear of the device and subsequently connect
the plug to the mains. Follow the instructions given in
paragraph 6.4. meticulously.
Fig. 3: Before starting work, place the protective cap (x)
in the induction chamber. This collects drops of wax and
keeps the appliance clean.
Fig. 4: Turn the appliance on by pressing the ON/OFF
switch (fig. A, 3). The appliance is now in stand-by. This is
indicated by the green light on the front panel.
Failure to comply with any of the above-stated
equipment installation regulations can lead to
equipment malfunctioning and render the
warranty null and void.
6.6

DECLARED USE

The cyclope is designed to heat metal spatulas and similar
instrument used to model objects made from dental wax.
6.7 NON-DECLARED/PROHIBITED USE
Using the equipment for any purpose not
considered in paragraph regarding "Declared use"
shall be considered improper and thus forbidden.
The improper use of the equipment renders
the warranty null and void and Zhermack Spa
declines all liability for any damage to objects
and injury to operators or third parties.
The main reasons for which the warranty is rendered null
and void are given in paragraph 2.2 and in the "Warranty
Certificate" attached to this Manual.
20
The reference figures can be found on pages 3 and 4 of this manual.
CHAPTER 7: USING THE EQUIPMENT
7.1

GENERAL WARNINGS

The tool heater must not be used near
pacemaker wearers.
For total certainty of safe operation, scrupulously
follow the work phases given below.
• Do not place fingers with metal rings in the
induction chamber; risk of burns.
• Do not leave metal objects in the induction
chamber for too long or they may become
incandescent.
• To avoid the occurrence of any risks, pay
attention to avoid pouring water during the
preparation on the electrical voltage parts.
• To avoid damage to the appliance:
- Do not place metal objects near the coil, this
could jeopardise correct operation of the
tool heater.
- Heating occurs only when metal objects are
placed in the chamber. Do not insert other
materials.
- Keep the outside frame of the appliance free
from molten wax.
7.2

USING THE TOOL HEATER

Once it has been correctly installed and put into service,
proceed as follows:
Fig. 5: Heat the spatula (y) by placing it at the centre of
the induction chamber, making sure it does not touch the
inside wall.
Induction is activated by the position sensors which
detect the presence of the instrument. The red and green
LEDs light up alternately.
To prevent overheating of the coil, the appliance
has a fan which is activated automatically when
the temperature inside the appliance starts to rise.
Fig. 6: The heating process stops automatically when
the instrument is removed from the chamber (green LED
on steadily). At the end of the working session, turn the
appliance off using the ON/OFF switch.
Cyclope has a safety system which interrupts induction
if the presence of an instrument in the chamber for an
excessively long period is detected. When this occurs, the
red LED flashes rapidly. To stop the flashing, just remove
the instrument from the induction chamber. If the flashing
continues, turn the tool heater off then on again. If the
anomaly occurs again, you must calibrate the sensitivity
of the position sensors as this is greatly influenced by
numerous external factors such as temperature, humidity,
light, etc.
7.3

CALIBRATING THE POSITION SENSORS

The sensitivity of the sensors is set to detect the majority
of wax modelling instruments. However, the sensors can
cyclope