Kärcher KM 90/60 R P Adv Manual Del Usuario página 19

 Slide the four support beams included
in the packaging under the ramp.
 Remove the wooden blocks used for ar-
resting the wheels and slide them under
the ramp.
 Slide the machine over the prepared
ramp from the pallet.
The machine can be moved in 2 ways:
(1) By pushing it (see Moving sweeper
without engaging self-propulsion).
(2) By driving it (see Moving sweeper by
engaging self-propulsion).
Moving sweeper without engaging
self-propulsion
Danger
Risk of injury! Before engaging the free-
wheel operation, the machine must be se-
cured to prevent it rolling away.
 Open the device hood.
 Engage the freewheel lever in the upper
position.
Note: If the freewheel lever does not
lock in, then slightly move the machine
forward and backward.
Position freewheel lever up - appliance can be
moved (view from behind)
Caution
Risk of damage to the hydrostatic axle
drive!
Only push sweeper slowly and across short
distances.
The travel drive is inoperable.
–
Braking effect exists no more.
–
 After moving the appliance, snap the
freewheel lever into the lower position.
 Close cover.
Moving sweeper by engaging
self-propulsion
 Open the device hood.
 Engage the freewheel lever in the lower
position.
Position freewheel lever down - appliance is
ready to start.
 Close cover.
Start up
General notes
Note: The machine has been fitted with an
automatic parking brake that is activated as
soon as the engine is switched off and the
driver leaves his seat.
 Park the sweeper on an even surface.
 Remove ignition key.
Prior to start/safety test
Maintenance Works
 Check engine oil level.
 Check the filling level of the fuel tank at
the fuel gauge.
 Check fill level of hydraulic oil.
 Check side brush.
 Check the roller brush for wear and
wrapped belts.
 Empty waste container.
 Check tyre pressure.
 Check function of seat contact switch.
 Check, if the stop switch on the com-
bustion engine is in the "ON" position.
Note: For description, see section on Care
and maintenance.
Refuelling
Danger
Risk of explosion!
Only fuel up while motor is turned off.
–
Only use the fuels specified in the Op-
–
erations Manual.
Do not refuel the machine in enclosed
–
spaces.
Smoking and naked flames are strictly
–
prohibited.
Ensure that no fuel reaches the hot
–
open surfaces.
4
-
EN
1 Tank lid
2 Tank indicator
3 Fuel tap
 Switch off engine.
 Open the device hood.
 Read the filling level at the fuel gauge.
The red area indicates the filling level.
 Open fuel filler cap.
 Use and install a funnel with a filter.
 Use "regular unleaded petrol".
Tank filling with empty tank approx. 5 li-
tre
 Wipe off any spilt fuel, remove funnel
and close fuel filler cap.
 Close cover.
Operation
Caution
Risk of damage to the drive! Prior to each
run, ensure that the freewheel lever is in the
lower position.
Caution
The air inlets next to the driver's seat must
not be covered. Do not store any objects
next to or behind the seat.
Warning
Long hours of using the appliance can
cause circulation problems in the hands on
account of vibrations.
It is not possible to specify a generally valid
operation time, since this depends on sev-
eral factors:
Proneness to blood circulation deficien-
–
cies (cold, numb fingers).
A firm grip impedes blood circulation.
–
Continuous operation is worse than an
–
operation interrupted by pauses.
In case of regular, long-term operation of
the device and in case of repeated occur-
rence of the symptoms (e.g. cold, numb fin-
gers) please consult a physician.
Adjusting driver's seat
 Pull seat adjustment lever inwards.
 Slide seat, release lever and lock in
place.
 Check that the seat is properly locked in
position by attempting to move it back-
wards and forwards.
19