ATIKA BF 43-2 Manual Original página 22

replacing the cutting tool
−
Leaving the machine (also during temporary interruption)
−
Maintain the machine carefully:
•
Follow the maintenance instructions and the instructions
−
for tool exchange.
Keep the handholds dry and free from resin, oil and
−
grease.
Always keep the machine including tool in a good
−
condition.
Make sure to check the machine before any use and
−
after dropping or other impacts to ensure that it is in a
proper condition.
Check the machine for possible damage:
•
Before continuing to use the machine, the protective
−
devices must be inspected to ensure that they work
perfectly and with their intended function. Only operate
the machine with complete and correctly attached safety
equipment and do not alter anything on the machine that
could impair the safety.
Check whether the movable parts function perfectly and
−
do not stick or whether the parts are damaged. All parts
must be correctly installed and fulfil all conditions to
ensure perfect operation.
Damaged guards and parts must be properly repaired or
−
exchanged by a recognized, specialist workshop; insofar
as nothing else is stated in the instructions for use.
Damaged or illegible security labels have to be replaced.
−
Do not allow any tool key to be plugged in!
•
Before switching on, check always that all tools are removed.
Store unused equipment in a dry, locked place out of the
•
reach of children.
Note that a failure to maintain the unit properly, any use of
•
non-conform spare parts or a removal / modification of
safety devices can result in damages to the machine and to
serious injuries of the person who works with it.
Do not carry out repair operations on the machine other
than those described in section "Maintenance and care"
but contact the manufacturer or authorized customer
service centre.
Use only original spare parts. Accidents can arise for the
user through the use of other spare parts. The
manufacturer is not liable for any damage or injury
resulting from such action.
Behaviour in an emergency situation
 Initiate all required first aid measures suited for the injury
and seek qualified medical advice as quickly as possible.
 Protect the injured person against further injuries and
immobilise the injured person.
Safety instructions - Safe handling of fuels
Fuels and fuel vapours are inflammable and may
cause serious injury on the skin or when inhaled.
Therefore be careful and provide sufficient
ventilation when handling with fuels.
Do not smoke and avoid open flames when fuelling.
•
Wear gloves when fuelling.
•
Do not fuel in closed rooms.
•
22
Stop the device and allow it to cool down.
•
Carefully close the tank cap after fuelling and check that it
•
does not get loose during operation.
Avoid spilling of fuel or oil. Clean the device immediately
•
when you have spilled fuel or oil. Change your clothes
immediately when you have spilled fuel or oil on them.

Make sure that no fuel can enter the soil.
•
Check that there is no leakage on the tank cap and fuel lines.
•
If there are leaks this product may not be started.
Never use a device with damaged ignition cable and spark
•
plug connector. Risk of sparking.
Transport and store fuels and oil
•
only in containers approved and marked for this purpose.
−
not close to combustible and highly flammable materials
−
as well as sparks and open flames.
Keep children away from fuels.
•
Go away at least three meters from the fuelling place to start
•
the device.
Description of device
 Please refer to the attached assembly and operating
instruction sheet.
Pos. Denomination
1 Drive unit
2 Lower tube shaft with angular gear
3 Handle with safety switch
4 Carrying strap
5 Handle
6 Safety guard
7 Cutting blade
8 Thread spool
8A Thread spool roll
8B Spool cover
8C Washer
8B Compression spring
9 Fuel mixing can
Locking handle
10
11 Allen key, size 4
12 Allen key, size 5
13 Open-end wrench, size 8/10
14 Socket wrench
Screwdriver
15
16 Cable tie
17 Gas cable
18 Air filter cover
19 Spark plug connector
Silencer
20
21 Cranking handle
22 Fuel tank
23 Tank cap
24 Choke lever
Priming pump
25
26 Suspension eye
27 Angular gear
28 Safety guard holder
29 Thread knife
30 Safety handle
Order-No
385810
385805
382826
385806
385804
385803
385838
385839
385840
385837
380786
385820
385814
385817
385825
385807
385808