Tools And Parts; Location Requirements; Product Dimensions - arietta ALS436SS Guía De Instrucciones Para Instalación

Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
CAUTION:
Remove carton carefully, Wear gloves to protect against sharp
edges.
Tools needed (all models)
■ Wire nuts
■ Metal duct lenght to suit installation
⁄
■ " Romex wire connector
1
2
■ 6" rounded metal duct lenght to suit installation
■ Measuring tape
■ Pliers
■ Gloves
■ Knife
■ Safety glasses
⁄ "
■ Electric drill with and
5 3
16
■ Spirit level
■ Duct tape
■ Screwdrivers:
■ Philips (Posidrive #2)
■ Torx #2
■ Wire cutter/ stripper
■ Masking tape
■ Hammer
■ Saw, jigsaw or reciprocating saw
Parts Supplied
Remove parts from packages. Check that all parts are included.
■ Hood canopy assembly with blower.
■ Lamps already installed.
■ Air transition
■ Grease filter
■ Duct covers
■ Hardware package. Includes:
• Template
• Duct cover support bracket (1 piece)
• Use, care and installation guide
• Wood screws (6 pieces-
• Concrete wall anchors (6 pieces-
• Assembly screws (4 pieces - 4.2 x 8 mm)
• Air transition screws (2 pieces - 3.5 x 9.5 mm)
• TORX 10 adapter
• TORX 20 adapter
Optional Accesories
■ Recirculation KIT (KIT01937).
†®TORX is a registered trademark of Saturn Fasteners, Inc.

Tools and Parts

⁄ "
Bits
8
5 x 45 mm)
8 x 40 mm)

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.
Have a qualified technician install the range hood. It is the
installer's responsibility to comply with installation clearances
specified on the model/serial rating plate. The model/serial rating
plate is located behind the left filter on the rear wall of the vent
hood.
Canopy hood location should be away from strong draft areas,
such as windows, doors and strong heating vents.
Cabinet opening dimensions that are shown must be used. Given
dimensions provide minimum clearance.
Grounded electrical outlet is required. See "Electrical Require-
ments" section.
The canopy hood is factory set for venting through the roof or
wall. For non-vented (recirculating) installation, the KIT01937
must be purchased with your provider.
For Mobile Home Installations
The installation of this range hood must conform to the
Manufactured Home Construction Safety Standards, Title 24
CFR, Part 328 (formerly the Federal Standard for Mobile Home
Construction and Safety, Title 24, HUD, Part 280) or when such
standard is not applicable, the standard for Manufactured Home
Installation 1982 (Manufactured Home Sites, Communities and
Setups) ANSI A225.1/NFPA 501A, or latest edition, or with local
codes.

Product Dimensions

10 ⁄ "
3
4
(27.3 cm)
13 ⁄ "
3
16
(33.5 cm)
30" (76.2 cm)
or
36" (91.4 cm)
3
6"
(15.24 cm)
Ductless (recirculating)
version only
*Max 42 ⁄ " (108 cm)
9
16
*Min 28 ⁄ " (71.7 cm)
4
16
Ducted version only
*Max 38 ⁄ " (98.76 cm)
14
16
*Min 24 ⁄ " (62.4 cm)
9
16
5"
(12.6 cm)
19 ⁄ "
11
16
(50 cm)