Installazione Con Valvole; Fornite Dall'installatore; Installation W Ith Valves - Trane CWS 00-2P Guia Tecnica

Ocultar thumbs Ver también para CWS 00-2P:
Tabla de contenido

Publicidad

TA = Termostato ambiente
Room thermostat
Thermostat d'ambiance
Raumthermostat
Termostato ambiente
Thermostat omgevingstemperatuur
36
INSTALLAZ IONE
CON V ALV OLE
F ORNITE
DALL'INSTALLATORE
• Per l'installazione delle valvole se-
guire le istruzioni del costruttore;
per realizzare i collegamenti al
Cassette fare riferimento ai disegni.
• Per evitare che negli impianti ad
acq ua fredda la condensa vada a
gocciolare sul sofitto, isolare bene
le tubazioni, le valvole e gli attacchi
della batteria.
Sch em i elettrici
d i colleg am ento valvole
• Per il collegamento del comando
scelto seguirele istruzioni allegate
allo stesso.
ATTENZ IONE:
• I cavi devono passare attraverso
gli appositi passacavi e parastrappi.
• Le valvole devono essere collega-
te seguendo gli schemi elettrici sug-
geriti.
• Le valvole da utilizzare devono
bloccare l'ingresso acq ua q uando
è assente la tensione di alimenta-
zione.
• Se non si rispettano i collegamenti
proposti, si correrà il pericolo di
avere la tracimazione dell'acq ua
dalla vaschetta raccogli condensa.
• È fondamentale che le valvole acq ua
si chiudano nel momento stesso in
cui il contatto interno della scheda
tra i morsetti 2 e 3 si apre.
• Il contatto tra il polo 2 e il polo 3
rimane chiuso inchè il livello della
condensa all'interno della vaschet-
ta non raggiunge il massimo livello
consentito.
• È fondamentale che le valvole si
aprano solo nel momento in cui il
ventilatore funziona ad una delle
tre velocità.
• Controllare la tenuta nei punti più
critici dell'impianto q uando lo si
riempie di liq uido per la prima volta.
• Il costruttore declina ogni responsa-
bilità nel caso di malfunzionamento
o danni causati dal gocciolamento
di gruppi di valvole acq uistati ester-
namente dall'installatore.
Nel caso l'installatore decidesse di uti-
lizzare delle valvole solenoidi acq ua di
zona anzichè singole valvole acq ua
montate su ciascun apparecchio, oc-
correrà collegare elettricamente la val-
vola in maniera tale che vada in chiu-
sura nel caso che uno q ualsiasi degli
apparecchi si fermi a causa del proprio
sistema di sicurezza; per l'esecuzione
dell'impianto suggeriamo di utilizzare
lo schema a lato riportato.
INSTALLATION
W ITH V ALV ES
PROV IDED
B Y THE INSTALLER
• F or the installation of the valves,
follow the instruction of the producer;
to mak e the connection to the Cassette,
please mak e reference to the drawings.
• In cold water installation, to avoid
that the condensate drops on the
ceiling, it is necessary to insulate
the piping, the valves, and the coil's
connections.
V alves
electric w iring d iag ram s
• F or the connection of the selected
control, follow the instructions included
with the control itself.
ATTENTION:
• The cables must pass through the
apposite fairleads and lex ible couplings.
• The valves must be connected
according to the suggested electric
wiring diagrams.
• The valves used must stop the
entering of the water when there is
no electrical feeding.
• If the proposed connections are
not respected, there will be the risk
that the water overlows from the
condensate collection tray.
• It is necessary that the water valves
close at the same time when the
internal contact of the card between
terminals 2 and 3 opens.
• The contact between the pole 2
and the pole 3 remains closed until
the level of the condensate inside
the tray reaches the max imum
allowed level.
• It is important that the valves open
only when the fan is work ing at one
of the three speeds.
• Check the seal in the most critical
points of the plant when it is illed
of liq uid for the irst time.
• The manufacturer cannot be consider
responsible in case of bad work ing
or damages due to the drop of valves
sets purchased directly by the installer
from other suppliers.
Should the installer decide to use
some "zone" magnetic water valve
instead of single water valves mounted
on each unit, it will be necessary to
connect electrically the valve so that
it closes in case that one of the units
stops because of its safety system;
for the ex ecution of the installation
we suggest to use the below diagram.
UNT-SVX03J-XX

Publicidad

Tabla de contenido
loading

Tabla de contenido