Controls And Indicators - Cub Cadet 17BICBDT603 Instrucciones De Funcionamiento Originales

Operating Manual
Installing the seat
Fig. 2d
Note
When attaching the seat, do not
damage the seat switch cable!
Push excess cable back into the
opening of the seat support.
Mount discharge flap on the
mower deck
Fig. 2e
Remove nuts (1) from the carrier

pins (2).
Mount discharge flap (3) on the

carrier pins (2) and attach with
the nuts (1).

Controls and indicators

Warning. Damage to the unit.
First of all the functions of the
controls and indicators are
described here. Do not execute
any functions yet!
Fig. 1
1 Forward pedal
2 Reverse pedal
3 Pedal for parking brake/
cruise control
4 Cutting height adjustment lever
5 Throttle/Choke *
6 Combination indicator *
7 Choke *
8 PTO switch
9 Can holder
10 Ignition lock *
11 Storage bin
12 Gear release lever
13 Fuel tank
14 Seat adjustment lever *
15 Steering wheel
16 Brake pedal
(* depending on model)
Forward pedal (1)
Fig. 8
The pedal controls the speed
in a forward direction.
Reverse pedal (2)
Fig. 8
The pedal controls the speed
in a reverse direction.
Information on forward/reverse
pedal
To stop or change direction of
travel, release the appropriate
pedal.
Parking brake/
Speed control (3)
Fig. 8
This pedal has a dual function:
Actuate the parking brake
Depress brake pedal (16) all the
way and press pedal.
Release the parking brake.
Depress brake pedal (16) all the
way, pedal is released.
Switching on Tempomat
When driving, press the pedal.
The forward speed selected at this
point (but not top speed) is main-
tained, and the drive pedal can be
released.
When the forwards accelerator
pedal or brake pedal is depressed,
the cruise control is automatically
switched off.
Cutting height adjustment
lever (4)
Fig. 1
Largest cutting height, cutters top =
lever to "H/8".
Smallest cutting height, cutters
bottom = lever to "L/1".
Note
Smallest cutting height ~3,8 cm.
Largest cutting height ~10 cm.
Choke (7/5, depending on
model)
Fig. 5
To start a cold engine, pull out the
choke (fig. 5a) or set the throttle to
position (fig. 5b).
Throttle (5)
Fig. 4
Set engine speed steplessly.
Fast engine speed =
Slow engine speed =
Combination indicator (6)
(optional)
Fig. 7
According to the model, the
combination indicator can consist
of the following elements.
Oil pressure (1):
The indicator light is lit while the
engine is running, immediately
switch off engine and check oil
level. Where necessary, visit
a garage.
Brake (2):
Indicator lamp lights up if the brake
pedal is not depressed or the
parking brake is not locked when
.
the engine starts.
Cutter deck (PTO) (3):
The indicator lamp lights up when
the cutters are not switched OFF
at engine start (PTO).
Battery charge indicator (4):
:
If the indicator light lights up when
the engine is running, this means
that the battery is not sufficiently
charged. Where necessary, visit
a garage.
Operating hour counter (5):
Indicates the operating hours in
1
hours and
Ampere meter (6):
This shows the charging current
from the generator to the battery.
Optional functions
(depending on model)
Fig. 7a: Type 1
Fig. 7b: Type 2
Operating hour counter
(type 1, type 2):
When the ignition is switched on,
the battery voltage indicator is
indicated for a short period and
then the operating hours are
indicated. The operating hours are
always counted except for when
the ignition key is in the „Stop"
position or when it is removed.
Oil change display (Type 1):
Each time 50 operating hours have
elapsed (according to the model),
the oil change indicator „CHG/OIL"
appears in the display for five
minutes. This message appears
.
after the next two hours of
.
operation. See the engine manual
for oil change intervals.
English
/ hours on the display.
10
7