emmeti MIRAI - SMI 4.0 Manual De Instrucciones página 77

1. DESCRIZIONE DEI COMPONENTI INDEX
1. Product introduction ................ 78
1.1 Features
1.2 Advanced Technology
1.3 Easy installation and service
1.4 Accessories
1.5 Principal components
1.6 Unit dimensions
1.7 Conformity to European Directives
2. Technical specifications ............ 82
2.1 Flow rate, useful prevalence and absorbed power of circulator
2.2 Operating range
3. Movement and transport .......... 85
3.1 Packing
3.2 Identification unit: Rating label
3.3 Handling units
3.4 Unpacking
4. Warnings ................................. 87
4.1 Extract from refrigerant gas R 32 safety data sheet
4.2 Attention and dangers
4.3 Prohibitions and warnings for installation
5. Installation ............................... 91
5.1 Minimum operating spaces for maintenance
5.2 Fixing
5.3 Condensate drainage pipes
5.4 Hydraulic system
5.5 Electrical system
5.6 Connection Specifications Recipe 1 (C400=1)
5.7 Connection Specifications Recipe 2 (C400=2)
5.8 Connection Specifications Recipe 3 (C400=3)
5.9 Connection Specifications Recipe 10 (C400=10)
5.10 Connection Specifications Recipe 13 (C400=13)
6. Types of installation ................ 107
6.1 Diagram 1: Hydraulic connection
Radiant system + Fancoil + Eco Hot Water - Recipe 1: C400=1 -
Par 407=0
6.2 Diagram 2: Hydraulic connection
Radiant system + Fancoil + Boiler x DHW (Euro HPV)
Recipe 1: C400=1 - Par C407=1
6.3 DIAGRAM 3 Hydraulic connection
Radiant system + Fancoil + ECO HYDRO KIT + Boiler
Recipe 2: C400 = 2
6.4 DIAGRAM 4 Hydraulic connection
Radiant system + Fancoil + ECO HYDRO KIT + BOILER
+ FEBOS-CHRONO Recipe 10: Par. C407 = 1
Thanks you for the trust you have shown by purchasing this product. Carefully read this manual which contains the specifications and all the information useful for the correct
functioning. Thanks you for the trust you have shown by purchasing this produtc. Carefully read this manual which contains the specifications and all the information useful for
the correct functioning. Warning! Keep these manuals in a dry place avoiding in this way to spoil them.
7. THERMOREGULATOR SMART MT ........ 115
7.1 Display and Keys
7.2 Parameters list - "Set" menu
8. USER SECTION: OPERATION ..........127
8.1 Heat Pump ON/OFF
8.2 Operating mode (Heating / Cooling)
8.3 Consent from Ambient Thermostat
8.4 Temperature setting of Water Set and Climate Curves
8.5 Consent and Set Point 2 setting
8.6 Activation of the circulator inside the PdC (heat pump)
8.7 Modulation of the PdC compressor
8.8 Compressor frequency limitation
8.9 Heating of domestic hot water (DHW)
8.10 Relaunch circulator
8.11 Additional heater
8.12 Frost protection
8.13 Outdoor air temperature sensor
8.14 Water flow rate
8.15 Electrical powers
8.16 Dehumidifier
8.17 Active alarms
8.18 Alarm history
8.19 High temperature radiant system alarm inpu
8.20 Low pressure systrem alarm input
9. Alarm codes on Smart-MT ........ 136
9.1 Troubleshooting
9.2 Alarm codes on Smart-MT
9.3 Manual reset protection status on the heat pump
10. Codes and alarms on pcb display ... 138
10.1 Alarm codes on PCB Display
11. Service and maintenance ......... 144
11.1 Alarm codes on the PCB Display
12. Cleaning ................................ 148
12.1 Cleaning the heat pump
12.2 Condensate water drain check
13. Disposal ................................ 149
13.1 WEEE information note
13.2 Packaging Disposal
Wiring diagrams ......................... 304
Product fiche ............................. 299
WARRATY .................................... 150
EN EN
77