Publicidad
Idiomas disponibles
Idiomas disponibles
2.2.4.
Electrical safety
•
Work at a minimum distance of 15 metres from live electrical cables.
•
Do not expose the tool before, during and/or after use to rain, wet environments, water, snow, ice, or any other
moisture conditions other than those permitted, in order to avoid the risk of electric shock and/or electrocution.
•
Keep the tool away from sources of heat, oil, solvents, and any environmental conditions other than those
indicated in the manual and permitted.
•
Keep it in a dry place.
•
Attention is drawn to the fact that in the event of damage or other condition with leakage of battery fluid, there
may be risks to personnel in the event of contact or other situation resulting from such leakage. Do not touch
any liquid from the battery pack. In case of contact, rinse immediately with clean water. If the liquid comes into
contact with your eyes, rinse thoroughly with clean water and immediately seek medical attention.
CAUTION!
Please refer to the documentation (manual, data sheet or pictograms) supplied with the Lithium battery
for all indications and warnings to be observed and concerning the use of the battery.
CAUTION!
Read the following instructions carefully. Failure to comply may result in electric shock, electrocution, fire
or damage to animals, property and/or persons.
2.3.
Use Warnings
2.3.1.
Warnings on the use of the tool
It is a mandatory requirement that the following conditions of prohibition and use be met.
Additional prohibition conditions:
•
Never use the tool if it is damaged, wrongly regulated or only partially assembled.
•
Do not use the power tool if the ON/OFF switch does not work correctly.
•
Do not use the tool while operating on a ladder, scaffolding or a surface that is not the ground level and/or not
a stable surface.
•
Never cut branches that are close to electric wires.
•
Never get distracted. Check what you are doing and use common sense when using the power tools.
•
Do not touch the chain while it is rotating
•
Do not touch the chain or carry out maintenance operations while the motor is on.
•
Do not use petrol, thinners or any aggressive and/or flammable products to clean the tool.
•
Do not cut above shoulder height.
•
Do not tamper with the tool's guards or command, control and safety devices.
•
Do not carry out cleaning and/or maintenance operations with moving parts.
•
Do not operate with the tip of the bar.
Conditions and requirements for use:
•
Before starting the tool, check that the chain is not touching any foreign bodies.
•
Get into a stable and safe working position, which guarantees perfect balance (for example a flat and dry
surface).
•
Use the tool, accessories, etc. in compliance with these instructions and considering the working conditions
and operations to be performed.
•
Always check before each use that the safety and command and control systems are in perfect working order.
•
Hold the tool handles (both power unit handle and pole handle) firmly with both hands.
•
Pay particular attention to the handles, which must always be dry, clean and free of oil residues, using the PPE
provided.
•
Be very careful when cutting bushes or small shrubs, since soft parts may get entangled in the chain and thrown
against the operator (always wear face protection PPE), or cause him to lose his balance.
•
Pay attention to kickback and upwards ricochet movements of the bar. They may cause the operator to lose
their balance or control of the tool.
•
Pay attention when cutting branches under tension, since they may cause loss of control of the tool due to a
whiplash effect.
•
Always keep the motor at high speed when cutting.
•
Remove any adjusting key before turning on the tool.
•
The chain may create sparks when touching hard materials while working. Please note that it is forbidden to
use the tool in potentially explosive environments, sparks can cause fires or explosions.
•
Keep the bar and chain clean and sharp.
•
Make sure that oil tank is always at least halfway full. Lack of oil causes seizing of the chain.
•
Inhaling atomised oil and/or wooden dust may cause irritation or intoxication of the operator's breathing system.
In case of prolonged ailments, consult a competent doctor.
Page 36
0310.0360 Use and Maintenance Manual - Translation
of Original Instructions - Rev: 00, Date 07/02/2024
Publicidad
