REMS Multi-Push SL Instrucciones De Servicio página 18

eng
1.1. Scope of Supply
REMS Multi-Push SL / SLW, electronic flushing and pressure testing unit with
compressor,
2 suction/pressure hoses 1", 1.5 m long, with hose screw fittings 1",
1 compressed air hose 8 mm, 1.5 m long, with quick couplings NW 5, for
pressure testing with compressed air,
1 high-pressure hose ½", 1.5 m long, with hose screw fittings ½", for pressure
testing with water (REMS Multi-Push SLW).
Seals for inputs and outputs.
Operating instructions.
1.2. Article numbers
REMS Multi-Push SL, electronic flushing and pressure testing unit,
pressure test with compressed air, without accessories
REMS Multi-Push SLW, electronic flushing and pressure testing unit,
pressure test with compressed air and water, without accessories
Disinfection unit TW
Cleaning and preservation unit H
Printer
Paper roll, pack of 5
REMS Peroxi Color
REMS CleanH
REMS NoCor
Test strips 1 – 100 mg/l H
Suction/pressure hose 1", 1.5 m long, with threaded hose fitting 1"
High-pressure hose ½", 1.5 m long, with threaded hose fitting ½"
Pneumatic hose 8 mm, 1.5 m long, with quick couplings NW 5
Connecting hose compressor/water connections
with threaded hose fitting 1" and quick coupling NW 5
Pneumatic hose pneumatic tools, 1.5 m long,
with quick couplings NW 7.2
Fine filter with filter cartridge 90 µm
Fine filter cartridge 90 µm
Caps 1" with chain (REMS Multi-Push)
Plugs 1" with chain (suction/pressure hoses)
Plugs ½" with chain (REMS Multi-Push)
Caps ½" with chain (high-pressure hose)
Pressure gauge 6 MPa/60 bar /870 psi
Fine scaled pressure gauge 1.6 MPa/16 bar/232 psi,
Fine scaled pressure gauge 250 hPa/250 mbar/3.6 psi,
1.3. Applications
Device storage temperature
Water temperature
Ambient temperature
pH value
Smallest test volume
Compressor
Operating pressure
Oil separation rate
Extraction rate
Compressed air vessel volume (Fig. 1 (35))
Condensation and particle filter
Flushing
Flushing water connections
Water pressure pipe network
Water pressure when flushing with compressed air ≤ 0.7 MPa/7 bar/101 psi
Water flow rate
Pipe diameter installation
Pressure test
Pressure test with compressed air
Reading accuracy < 200 mbar
Reading accuracy ≥ 200 mbar
Pressure test with water
Reading accuracy
1.4. Electrical/electronic data
Type of protection terminal box
Type of protection device, motor
Protection class
Operating mode (continuous operation)
Screen (LCD)
Resolution
Data transfer with USB stick
Printer, battery
Charger printer
1.5. Dimensions L × W × H
Paper roll printer B x Ø
1.6. Weight
REMS Multi-Push SL
REMS Multi-Push SLW
18
O
2 2
≤ 0.8 MPa/8 bar/116 psi
≤ 1 MPa/10 bar/145 psi
≤ 0.4 MPa/4 bar/58 psi
1 hPa/1 mbar/0.015 psi
100 hPa/100 mbar/1.5 psi
≤ 1.8 MPa/18 bar/261 psi
0.02 MPa/0.2 bar/3 psi
230 V~; 50 Hz; 1,500 W
110 V~; 50 Hz; 1,500 W
Ni-Mh 6 V, 800 mAh
Input 100 – 240 V~; 50 – 60 Hz; 0.15 A
Output
570 × 370 × 530 mm (22.4" × 14.6" × 20.9")
1.7. Noise information
Work place-related
Emission value
2. Start-up
CAUTION
Transport weights above 35 kg must be carried by at least 2 persons.
2.1. Electrical connection
WARNING
Caution: Mains voltage present! Before connecting the electronic flushing and
pressure testing unit, check whether the voltage given on the rating plate corre-
sponds to the mains voltage. Only use sockets/extension leads with a functioning
115600
PE contact. The function of the PRCD fault current circuit breaker (Fig. 1 (1))
must be checked every time before start-up and before beginning work:
115601
115602
1. Plug the mains plug into the socket.
115612
2. Press the RESET button (2), the PRCD control lamp (Fig. 1 (39)) lights red
115604
(operating state).
090015
3. Pull out the mains plug, the PRCD control lamp (39) must go out.
115605 4. Plug the mains plug back into the socket.
115607 5. Press the RESET button (2), the PRCD control lamp (39) lights red (oper-
ating state).
115608
6. Press the TEST button (3), the PRCD control lamp (39) must go out.
091072
7. Press the RESET button (2) again, the PRCD control lamp (39) lights red.
115633
The control lamp (Fig. 2 (5)) lights green. REMS Multi-Push is ready for
115634
operation after about 10 s.
115637
WARNING
115618
If the described functions of the PRCD fault current circuit breaker (Fig. 1 (1))
are not fulfilled, the device may not be used. There is a danger of electric shock.
115621
The PRCD fault current circuit breaker tests the connected device, not the
115609
installation before the socket nor interconnected extension leads or cable reels.
043054
On building sites, in a wet environment, indoors and outdoors or under similar
115619
installation conditions, only operate the electronic flushing and pressure testing
115620
unit on the mains with a fault current protection switch (FI switch) which interrupts
115624
the power supply as soon as the leakage current to earth exceeds 30 mA for
115623
200 ms. A cable cross-section that corresponds to the power of the electronic
115140
flushing and pressure testing unit must be selected when using an extension
115045
lead.
047069
Press the On/Off button on the input and control unit's operating panel (Fig. 2
(4)) for approx. 2 s, then release it. REMS Multi-Push is switched on and the
compressor switches on. The screen (6) is illuminated and the REMS Multi-
≥ 5°C
Push logo appears followed by the start menu:
5°C – 35°C
5°C – 40°C
Flushing
6,5 – 9,5
Disinfection
approx. 10 l
Testing
Compressed Air Pump
Memory Manager
oil-free
≤ 230 Nl/min
2.2. Menu structure and on-screen displays
4.9 l
Five main programs of the REMS Multi-Push are displayed in the Start menu:
5 µm
Flushing, Disinfection, Testing, Compressed Air Pump, Memory Manager. The
screen display contains a maximum 5 lines with 20 characters each. Lines with
defaults or test values are displayed language-independently with physical
DN 25, 1"
formula symbols, a uniform verbal abbreviation and the value of the test crite-
rion in the sub-routines. These have the following meanings:
≤ 5 m³/h
p refer bar xxx
≤ DN 50, 2"
p refer mbar xxx
p actual bar xxx
p actual mbar xxx
p diff bar xxx
p diff mbar xxx
t stabi min xxx
t test min xxx
Δ > 10K
PfS
P+M
p H O bar
IP 44 2
v H O m/s
2
IP 20
t H O min
2
I
n H O n-times
2
S 1
VA H O l
2
3.0"
VS H O l/min
2
128 × 64 bits
V H O l
2
USB port
File no.
max. DN
Enter
5 V=; 680 mA
Esc
Ver. Software
57 x ≤ 33 mm
2.3. Settings menu
NOTICE
36.7 kg (81 lb)
The defaults for the different test criteria in the settings menu of the REMS
39.0 kg (86 lb) Multi-Push are taken from EN 806-4:2010 or the information leaflet "Leak tests
L = 73 dB(A); L = 92 dB(A); K = ± 1 dB
PA WA
reference test pressure bar
reference test pressure mbar
actual test pressure bar
actual test pressure mbar
differential test pressure bar
differential test pressure mbar
stabilisation/wait time min
test time min
difference >10°C (10 Kelvin) water/environment
press fitting system (ZVSHK)
load test plastic + metal
water pressure
minimum flow speed
flushing time
water change
volume of the flushing section
volume flow
used water volume
memory location no. for measuring log
largest rated diameter
next screen display
previous screen display or cancel
version software
eng