Stiga SBC 627 K Manual De Instrucciones página 121

– Unscrew the middle knob (1) and remove the
cap (2).
– Insert the handle bar (3), making sure that the
controls are on the right.
– Set the handle bar in the most comfortable
working position and lock it using the cap (2)
and knob (1).
– Fasten the casing (4) of the controls to its ca-
ble fastener (5).
NOTE Loosening the knob (1) the handle bar can
be rotated to reduce its bulk for storage.
1.1c Models SBC 645 KD – 653 KD (Fig. 3)
– Lift the lever (1) and remove it loosening the
screw (2).
– Remove the cap (3) from the support (4).
– Put the handle bar (5) into the seat in the sup-
port (4), making sure that the controls are on
the right.
– Fit the cap (3) and lever (1), without tightening
the screw (2).
– Lower the lever (1) and check that the handle
bar (5) is firmly locked; if not, tighten the screw
(2) until it is satisfactorily locked.
– Fasten the casing (6) of the controls to its ca-
ble fastener (7).
NOTE Lifting the lever (1) the handle bar can be
moved to the position most comfortable for the
operator.
1.1d Models SBC 645 KF – 653 KF (Fig. 4)
– Slide the contoured plate (1) until it is close to
the holes in the drive tube (2).
– Fit the top part (3) of the front handgrip on the
plate (1) so that the pin (4) fits into one of the
three holes provided on the drive tube (2) to
adjust the handgrip to the operator's prefer-
ence.
– Join the bottom part (5) with the guard and at-
tach it to the top part (3), tightening the screw
(6) completely.
– Remove the protective cuffs (11) from both
ends of the flexible drive tube (12), taking note
that there are differences between them.
– Insert the end of the shaft (12a) in the seat of
the power unit, press the locking button (13)
and fully insert the flexible tube (12) into its
seating until the button (13) can be felt to rise.
– Insert the end with the groove (12b) in the
protruding hub of the front handgrip (14) and
fasten it with the screw (15) ensuring it stays
locked.
– Insert the register (17) of the throttle wire in
the support slot and connect the wire (18) to
the carburettor lever (19); then work the nuts
(20) to tighten the wire and block the register
on the support.
– Connect the two terminals of the cables (21)
and (22) to the corresponding cables on the
power unit.
1.2 FITTING THE GUARD ON THE CUTTING
DEVICE (Fig. 5)
WARNING! Each cutting device is pro-
vided with a specific guard. Never use guards
other than those indicated for each cutting
device.
WARNING! Wear protective gloves and
fit the blade guard.
– Remove the screw (1) from the guard (2).
– Insert the tab (3) in the guard seat (2) and fas-
ten the guard with the screw (1).
1.3 FITTING AND REMOVING CUTTING
DEVICES AND PREPARING GUARDS
WARNING!
ting devices or ones homologated by the
Manufacturer.
1.3.1 Selecting the cutting device
Choose the most suitable cutting device for the
job to be done, according to these general indi-
cations:
– the 3-point blade is suitable for cutting brush-
wood and small shrubs up to 2 cm in diameter;
– the 4-point blade is suitable for cutting tough
grass over large surfaces;
– the cutting line head can eliminate tall grass
and non-woody vegetation near fences, walls,
foundations, pavements, around trees, etc. or
completely clean a particular area of the gar-
den;
– the saw blade (if permitted) allows small
woody parts to be cut and small trees to be
felled.
Every cutting device must be fitted with a specif-
ic guard, as indicated by the following directions.
IMPORTANT The cutting devices are fastened
with a left-hand thread and therefore must be un-
screwed clockwise and screwed on anticlock-
wise. Remove all elements that may have been
assembled, which will be used in various con-
figurations, according to the cutting device used.
1.3.2 3 or 4-point blade "Tri-Arc" blade"
(Fig. 6)
5
Use only original cut-