Peq Configuration; Troubleshooting - Rotel RSP-1582 Manual De Instrucciones

30
NOTE: When ARC is enabled, the Rotel unit will play the audio from the
TV. The RSP-1582 volume can be controlled by the TV's remote control.

PEQ Configuration

PEQ CONFIGURATION
SPEAKER : Front Left
LF CONTOUR : 20Hz
FREQUENCY : 40Hz
FREQUENCY : 60Hz
FREQUENCY : 120Hz
FREQUENCY : 200Hz
FREQUENCY : 500Hz
FREQUENCY : 1200Hz
FREQUENCY : 4000Hz
FREQUENCY : 12000Hz
HF CONTOUR : 20000Hz
The PEQ CONFIGURATION menu allows you to enter EQ values for 10
bands as shown. PEQ setup requires advanced knowledge and equipment
for measuring the frequency response of the room and performance of the
speakers. To properly configure the EQ you should be familiar with the
tools and equipment needed. Typically these settings are only changed
by professional installers to ensure optimal performance of the RSP-1582.
Use the navigations buttons to highlight the frequency: Push the ENTER
button on the remote control or front panel to access and make changes.
Use the Up/Down arrow buttons to change the value. Use the Left/Right
arrow buttons to move to the next section on the line. Press ENTER again to
confirm settings and allow navigation to the next PEQ BAND.
FREQUENCY: There are 10 bands available and the frequency can be
changed between 10 - 24kHz as below.
BAND 1 LF CONTOUR: 10Hz - 40Hz, 1Hz Step
BAND 2 Freq: 20Hz - 44Hz, 1Hz Step
BAND 3 Freq: 45Hz - 89Hz, 1Hz Step
BAND 4 Freq: 90Hz - 180Hz, 10Hz Step
BAND 5 Freq: 190Hz - 350Hz, 10Hz Step
BAND 6 Freq: 360Hz - 690Hz, 10Hz Step
BAND 7 Freq: 700Hz - 1900Hz, 100Hz Step
BAND 8 Freq: 2kHz - 7.78kHz, 100Hz Step
BAND 9 Freq: 8kHz - 20kHz, 100Hz Step
BAND 10 HF CONTOUR: 8kHz - 24kHz, 100Hz Step
Q: The Q value can be adjusted between 1 to 10.
NOTE: Q for LF CONTOUR and HF CONTOUR are "1" and fixed.
GAIN: The gain can be set between -12 to +2.
To exit this menu press the BACK button or select "BACK" on the OSD then
press the SETUP/MENU button to return to normal operations.
NOTE: Q in EQ value relates to the bandwidth of the filter. The higher
the value, the narrower the bandwidth.
Q : 1 (Fixed) GAIN : 0
Q : 1 GAIN : 0
Q : 1 GAIN : 0
Q : 1 GAIN : 0
Q : 1 GAIN : 0
Q : 1 GAIN : 0
Q : 1 GAIN : 0
Q : 1 GAIN : 0
Q : 1 GAIN : 0
Q : 1 (Fixed) GAIN : 0
BACK
Default 20Hz
Default 40Hz
Default 60Hz
Default 120Hz
Default 200Hz
Default 500Hz
Default 1.2kHz
Default 4kHz
Default 12kHz
Default 20kHz
RSP-1582 Surround Sound Processor

Troubleshooting

Most difficulties in audio systems are the result of incorrect connections, or
improper control settings. If you encounter problems, isolate the problem
area, check the control settings, determine the cause of the fault and make
the necessary changes. If you are unable to get sound from the unit, refer
to the suggestions for the following conditions:
The unit does not turn on
• Make sure the power cord is plugged into the rear panel and a AC outlet.
• Make sure the rear panel POWER switch is in the ON position.
No sound from any input
• Make sure that MUTING is off and VOLUME is turned up.
• Make sure that preamp outputs are connected to a power amplifier
and that the amplifier is turned on.
• Make sure source inputs are connected and configured correctly.
• Check that the setting for AUDIO MODE in the VIDEO SETUP menu
is set to "Pre-Out Enable".
No sound from digital sources
• Make sure that digital input connector is assigned to the proper source
input and that the source input is configured to use the digital input
rather than an analog input.
• Check the configuration of the digital input source player to ensure
that the digital output is activated.
No sound from some speakers
• Check all power amp and speaker connections.
• Check Speaker Configuration settings in the Setup menus.
No Video Output
• Make sure that the TV monitor is connected properly and check the
input assignments.
• Check the source input and TV output resolution are compatible. An
HDMI 1080p source can only be sent to a 1080p compliant TV monitor.
• HDMI cables must be 5 meters or less in length.
• If watching 3D source, make sure the display is 3D enabled.
Video and Audio do not match.
• Check that the proper video source is selected for each input.
• Check that the group delay (lip-synch) setting is not mis-adjusted.