Thermo-Stop Function; Soft Models With Built-In Descaler (Mod "C") - Fagor evo CONCEPT Instrucciones De Instalación, Uso Y Mantenimiento

EN
The THERMOSTOP option allows activating / deactivating the Thermostop function.
The REGENERATION option (only in SOFT models) performs immediately a regeneration cycle of 15
minutes duration.
The HRS option modifies the HRS fan operating time (40 seconds by default).

5.2 Thermo-stop Function

When the thermo-stop is activated, the wash cycle is extended, if necessary, until the boiler reaches a rinse
temperature which will guarantee correct hygienisation in accordance with health regulations.
If the water input temperature is lower than 40 ºC / 104 ⁰F, the times required to
reach the operating temperatures will increase and productivity levels will
decrease. The thermo-stop function may extend the wash cycle times.
This function is only active as standard in models "B" and "C", which also have the EFFI-RINSE SYSTEM,
which always
To enable or disable this feature:
•
MOD "A" and MOD "B" appliances: With the machine off, simultaneously press buttons P1
and P2 for 5 seconds, which will enable or disable the thermostop as applicable.
The L2 light and the display will indicate the new status of the thermostop function for 5
seconds.
•
In MOD "C" machines, this function can be activated or deactivated using the User Menu.
(Chapter 5.1.1)

5.3 SOFT models with built-in descaler (MOD "C")

In the SOFT version machines, the dishwasher is fitted with an intake water descaler system.
If the water hardness is more than 45 ºfH / 31.5 ºeH / 25.2 ºdH, an external descaler must be installed.
The built-in descaler eliminates the water hardness resulting from excess calcium and magnesium, which
are the causes of scale on the appliance.
Before starting the appliance, fill the corresponding reservoir with regeneration salt for descalers (coarse
salt, max. grain size 5 – 7 mm, do not use tablets) and potable water (do not use common salt or any other
type of liquid).
To fill the regeneration salt reservoir, proceed as follows:
- Open the hood of the appliance.
- Remove the basket from the machine.
- Unscrew the salt reservoir cap located in the upper part of the tub.
- Using a funnel, pour regeneration salt into the reservoir. The first time, fill with 1 kg of regeneration
salt and top up the remaining space with potable water. On subsequent occasions, only add 0.5kg
of regeneration salt; the reservoir will have the required amount of water.
- Clean the seal and the edges of the reservoir carefully before replacing the cap in order to prevent
oxidisation.
- Replace the cap and tighten securely.
After analysing the hardness of the water, the technician should change the water hardness setting in
accordance with the measurements in the configuration menu.
DUREZA AGUA
70
ensures the correct
T-Stop enabled
/
L2 on 5 seconds
TERMOSTOP THERMOSTOP THERMOSTOP THERMOSTOPP THERMOSTOP
NO / SI /
ATRAS
WATER HARDNESS
0-9ºfH / 9-18ºfH / 18-27ºfH / 27-36ºfH / 36-45ºfH / >45ºfH
0-5ºdH / 5-10ºdH / 10-15ºdH / 15-20ºdH / 20-25ºdH / >25ºdH
sanitizing temperature
T-Stop disabled
L2 blink 5 seconds
NO / YES / NON / OUI /
BACK DERRIERE
DURETE DE L'EAU WASSERHARTE
and constant rinsing
/
NEIN /JA /
ZURUCK
DUREZZA ACQUA
pressure.
NO / SI /
RITORNO