SMA FUEL SAVE CONTROLLER 2.0 Instrucciones De Uso página 4

Table of Contents
6.9.1 Overview of Operating Modes and Setpoints .............................................................................................. 41
6.9.2 Displaying Setpoints and Actual Values......................................................................................................... 42
6.9.3 Configuring the Operating Mode................................................................................................................... 43
6.9.4 Specification of Setpoints for PV Power Plant by SCADA System ................................................................ 43
7 System Settings............................................................................................................................. 44
7.1 Configuring the Utility Grid............................................................................................................................. 44
7.2 Settings for the gensets.................................................................................................................................... 44
7.2.1 Parameters for Gensets without the Genset Controller.................................................................................. 44
7.2.2 Parameters for gensets with genset controller easYgen-3000 via the CAN network ................................. 45
7.2.3 Parameters for Gensets with Genset Controller easYgen-3000 via the ESENET Gateway ....................... 47
7.2.4 Parameters for Gensets with Genset Controller ComAp IG-/IS-NTC........................................................... 48
7.2.5 Configuring Gensets ........................................................................................................................................ 49
7.3 Configuring the PV Power Plant...................................................................................................................... 50
7.4 Setting the Storage System ............................................................................................................................. 53
7.5 Settings on the Measurement Devices ........................................................................................................... 55
7.5.1 Making General Settings on Measurement Devices ..................................................................................... 55
7.5.2 Making Detailed Settings on Measurement Devices for Internal Measurement Modules of the SMA
Fuel Save Controller ....................................................................................................................................... 57
7.5.3 Making Detailed Settings on Measurement Devices for Data Acquisition Modules................................... 59
7.5.4 Activating/Deactivating Devices..................................................................................................................... 61
7.6 Setting the Temperature and Irradiation Sensors .......................................................................................... 62
7.7 Configuring Stop of the Fuel Save Controller via Switch Input DI 7 ............................................................ 63
7.8 Setting Analog Inputs ...................................................................................................................................... 65
7.9 Handling System Settings................................................................................................................................ 67
7.9.1 Ending System Settings .................................................................................................................................... 67
7.9.2 Saving System Settings .................................................................................................................................... 68
7.9.3 Loading System Settings .................................................................................................................................. 68
7.9.4 Deleting System Settings.................................................................................................................................. 69
8 System Control ............................................................................................................................. 70
8.1 Genset control ................................................................................................................................................. 70
8.1.1 Configuring the Minimum Genset Load Threshold ........................................................................................ 70
8.1.2 Configuring Reverse Power Protection of the Gensets .................................................................................. 71
8.1.3 Setting the Supply of Sufficient Reserve Power via Gensets ......................................................................... 73
8.2 Controlling the PV power plant....................................................................................................................... 77
8.2.1 Setting the Power Factor Control for the Gensets Using the Reactive Power Release of the PV Inverters . 77
8.2.2 Setting the Control of the PV Power Plant Reactive Power According to Electrical Load............................ 80
8.2.3 Configuring MPP Calculation for PV Power Plant .......................................................................................... 83
8.3 Controlling the Battery Inverter ....................................................................................................................... 84
8.3.1 Setting the State-Of-Charge Control of the Battery........................................................................................ 84
8.3.2 Setting the Setpoints for the Storage System According to the Rise and Drop of PV Power ...................... 87
8.3.3 Setting the Charge/Discharge of the Battery According to the Rise/Drop in PV Power............................. 88
8.4 Controlling the Fuel Save Controller .............................................................................................................. 91
8.4.1 Configuring Setpoint Change Rate for PV inverters and Gensets................................................................. 91
8.4.2 Options for Specifying the Reserve Power Setpoint of the Gensets ............................................................. 93
8.4.3 Configuring PV Power Plant Management..................................................................................................... 94
8.5 Setting the Control of the Grid Feed-In .......................................................................................................... 96
9 System History.............................................................................................................................. 98
9.1 Overview of the Data Structure ...................................................................................................................... 98
4 FSC20-BA-xx-20
SMA Solar Technology AG
User Manual