Overview Of Controls - Uline OHAUS EXPLORER H-4737 Manual Del Usuario

FUNCTIONS AND THEIR ICONS
Seven icons are initially available to operate the balance
and access the menu. For setup information, see User
Settings.
Standby: Touch STANDBY to shut down the display.
NOTE: After initial start-up, in Standby your
balance needs no warm-up time and is
immediately available for weighing by
touching the Start-up icon.
Printing Data: Touch PRINT to send the
displayed value to a printer or computer via the
active COM port.
NOTE: Ensure proper setup of connections,
printing and interface parameters. Data may
also be printed using the TouchLess sensors
by configuring these for Printing. Data may
also be printed using the P command from a
computer connected to the COM port.
Zero Operation: Remove the load from the pan
and touch ZERO to set the display to zero. When
weighing pan is empty, the >0< indicator turns on
when the measurement is within ± 1/4 division (d)
of the zero setting.
NOTE: The balance also features Auto Zero
Tracking (AZT) that automatically maintains a
Center of Zero within the tolerances set in the AZT
menu (See Balance Settings).
TouchLess Sensor Status: Explorer balances have
four TouchLess sensors that can be assigned a
unique function when activated (e.g., zero, print,
tare, Automatic draftshield door etc.). To assign a
task for each TouchLess sensor, press SENSORS.
NOTE: To activate a sensor, move an object over it
(From a distance of 1-2 inches or 3 cm). The sensor
shows a green light and beeps when activated. If
the sensor cannot be activated (sensor is disabled
during certain instances, like when the Menu is
displayed) the sensor shows a red light.
AutoCal™: When AutoCal™ is ON, the balance
performs a self-calibration. AutoCal™ will
automatically calibrate the balance (using
the internal mass) each time a change in
temperature significant enough to affect
accuracy, or after every 11 hours. Touch AutoCal™
to initiate. (Default status is ON.)
PAGE 2 OF 96

OVERVIEW OF CONTROLS

• Perform a numeric operation using the keypad.
• Press = to view the result.
• To clear the display: Press CE to clear the entry, C to
• Touch X to close and return to the current application.
Menu: Touch MENU to enter the balance's
menu list.
More...: Touch MORE to access Level Assist, Zero,
Tare, Units, Pretare, Cal Test, Calculator and
Stopwatch.
Level Assist: For assistance with leveling the
balance; the Level Assist screen shows which
direction to turn the thumb wheels to center the
level bubble.
Applications: The balance can be configured
to operate in various application modes. Touch
APPLICATIONS to choose – or the top button in
the application area.
Taring a Container: Taring sets the weight of a
container as zero, so only the weight of objects
held in the container (net weight) is displayed.
Manual Tare: Place the empty container on the
pan and touch TARE when stable. Add material
to the container. The net weight of the material
is displayed. To clear the Tare value, remove the
container from the pan and touch TARE.
Weighing Units: The balance can be configured
to measure in a variety of weighing units,
including three custom units. Touch UNITS to
choose from the displayed list.
NOTE: The active weighing Unit can also be
accessed by touching the unit area of the
Main Display line; if a unit is not displayed in
the list, it must first be turned on via the User
Menu.
Preset Tare: To enter a preset tare, press the icon
and then enter a value; enter 0 to clear the
preset tare. The display will show the PT symbol
and the tare value as a negative number.
Calibration Test: Used to compare a known
calibration weight against the last stored span
calibration data.
Calculator: To use the built-in calculator
application, touch CALCULATOR. A four
function calculator with addition, subtraction,
multiplication and division mathematical
operations is available.
clear all.
NOTE: Calculator is not available in software
version 1.10.
0721 IH-4737