EMAK EF 92S/13H Manual Del Usuario página 51

7. TROUBLESHOOTING
Never perform a service operation if you do not have the appropriate qualifications and equipment. The
operations below can be performed by the user. Service operations other than those shown here will
void the warranty when performed by the user. The manufacturer is not liable for damages resulting
from the user's poor execution of prohibited service operations.
Problem
The machine cuts
unevenly
A strip remains
unmowed between the
blade rotors
The mowing
mechanism pulls the
turf
The mowing
mechanism does not
eject the grass
The mowing
mechanism's drive belt
stops during operation
The mowing
mechanism's drive belt
slips
The mowing
mechanism's drive belt
wears excessively
Set the blades in
motion
The blades stop late
 Remove clogged clippings from the underside of the mowing mechanism.
 Make sure the blades are sharp and not deformed.
 Check the blade tightness.
 Check the mowing mechanism's height adjustment. (
 Check the tension of the belts (
 Check the blade shaft. If it is damaged or overly worn, replace it.
 Check for damaged bearings. Repair or replace, if necessary. When mowing thick grass or
grass with an excessively wet surface, an unmowed strip may remain.The driving speed should
correspond to the right transmission gear for the mowing conditions. The engine should run
with a completely open throttle.
 Make sure the blades are sharp and not deformed. Replace the blades, if necessary.
 Check the tension of the belts (
 Check for damaged bearings. Repair or replace, if necessary.
 Check the mowing height and adjust it, if necessary. Turf is often pulled on uneven terrain.
 Check to see if the blades are warped. Replace the blades, if necessary.
 Remove clogged clippings from the underside of the mowing mechanism. Under wet conditions,
the removal tube and the underside of the mowing mechanism's exit port can be clogged with
grass. Do not cut wet grass.
 The driving speed should correspond to the right transmission gear for the mowing conditions.
The engine should run with a completely open throttle. When mowing tall grass, first mow
once at a high adjustment and then again at normal height. Abide by the information in chapter
5.5.3.
 Check the tension of the belts (
 Especially after replacing blades, make sure that the blade is installed correctly.
 The mowing mechanism's drive belt may be damaged if it jumps out of the pulley during
operation. If the belt still jumps out after trying the following steps, it must be replaced.
 Check the belt tension (
 Check the belt guide.
 Check the mowing height, and adjust it if necessary.
 Check to see if belt movement is being impeded by a foreign object. If it is, remove the object.
 Double check all pulleys. A bent or broken pulley can cause problems. Replace it, if necessary.
 Check the inner surface of the pulley on the engine. If it is rough or has cracks, the pulley
should be replaced.
 Check for worn-out parts in the tensioning mechanism, and replace them if necessary.
 If the grass is too tall or wet, the mowing mechanism's belt can slip. Check to see if the belt is
worn out. If it is, change it.
 Check the belt tension (
 Check the tension spring of the turnbuckle mechanism of the mowing belt.Replace the pulled
or damaged spring.
 Check all areas of the pulley guide. Check to see if belt movement is being impeded by a
foreign object. If it is, remove the object.
 Check the pulleys, and if they are damaged, replace them.
 Check the mowing height, and adjust it if necessary.
 Check the belt tension (
 Check to see if the belt is worn out or damaged. If it is, replace it. If it is loose, tighten it.
 Check the spring on the tensioning mechanism. Replace the broken or damaged spring.
 Check to see if belt movement is being impeded by a foreign object. If it is, remove the object.
 Check the belt tension (
tightened further due to considerable wear, replace it.
 Check to see if belt movement is being impeded by a foreign object. If it is, remove the object.
 Check the operation of the electromagnetic connector to see if it shuts off properly. If it
malfunctions, have it repaired or replaced by an authorized service facility.
Solution
6.3.8). If necessary, adjust the tension.
6.3.8). If necessary, adjust the tension.
6.3.8). If necessary, adjust the tension.
6.3.8). If necessary, adjust the tension.
6.3.8). If necessary, adjust the tension.
6.3.8). If necessary, adjust the tension.
6.3.8). If necessary, adjust the tension. If the belt cannot be
51
6.3.7). If it is not correct, readjust it.