Hendi 221594 Manual Del Usuario página 8

STAND-BY mode
• If the oven is not being used (it is not performing any operat-
ing functions), an acoustic warning („beep") is emitted after
10 minutes and the „STAND-BY" mode is activated automati-
cally. In this configuration the following are highlighted on the
display (in blue): the „Date and Time" and the symbol
EN
• After a further 10 minutes without operating functions, only
the symbol remains lit up on the display. To reactivate the
oven, touch the symbol
of the operating parameters related to „start-up" will light up
again on the display.
• If the oven is not being used, the „STAND-BY" mode can be
activated at any time by tapping on symbol
onds.
DATE and TIME settings
• These settings can only be made in „STAND-BY" mode.
• On the display, tap on the digits relating to „Date and Time"
(no 30 fig. 1). The bottom of the display shows the symbols:
, while the upper part of the display shows the
first 2 „digits" related to the Time value, which are set to be
modified by touching the symbols
symbol , confirms the set value and the next value to be
changed appears automatically.
• Proceed as shown below to set the desired values relating to:
"Minutes" - "Day" - "Month" - "Year".
• To exit the setting mode, touch the digits relating to "Date and
Time", and the display returns to "STAND-BY" mode.
• To activate the oven, touch the symbol
Operating parameters
SYMBOL PARAMETER
COOKING TIME
COOKING
TEMPERATURE
TEMPERATURE
ΔT TEMPERA-
HUMIDITY
FAN SPEED
Manual operation
General information:
• When anomalies occur during the operation of the oven that
prevent the continuation of the cooking cycle or the automat-
ic washing cycle, the display shows alarms with an acoustic
warning. Alarms are highlighted (in different colours) by the
letter "E" followed by the number that identifies the anomaly.
To reset the alarm touch the symbol
lights the "STAND-BY" mode (chapter "STAND-BY mode").
8
, and the „symbols" and „digits"
for a few sec-
and . Touching the
.
RANGE
from 1 minute to 11
hours and 59 minutes
or „INFINITE" time
(InF)
from 30°C to 270°C
(from 86°F to 518°F)
CORE from 1°C to 99°C
(from 33°F to 210°F)
from 1°C to 99°C
TURE (from 33°F to 210°F)
from OFF to 100% with
10% steps
from 0 to 3
: the display high-
• To reactivate the oven, touch the symbol
• T he various types of alarms are described in the relevant
chapter "Alarms".
PRE-HEATING setting:
• The PRE-HEATING function can be activated or disabled by
. touching the symbol
active the symbol becomes
perature value is preset at 40°C; however, by touching the
symbols or
to 150°C (in 10°C steps), , according to the different cook-
ing needs. For example, if a cooking temperature of 180°C
("step 1") and a PRE-HEATING temperature of 50°C are set,
a temperature of 230°C will be reached inside the cooking
chamber. An acoustic signal ("beep") warns when this tem-
perature is reached, which is maintained as long as the oven
door remains closed.
• Open the door (the acoustic signal is disabled) and put the
product to be cooked into the oven. Close the door: the cook-
ing cycle starts automatically.
IMPORTANT: The PRE-HEATING function cannot be used to-
gether with the delayed start. The PRE-HEATING temperature
cannot exceed 270°C.
Cooking TIME setting:
• Touch the 2 "digits" that indicate the "Hours" (no 27 fig. 1),
and set the desired value by touching the symbols
. Confirm the set value by touching the 2 "digits" of the
parameter or by touching the symbol
touch the 2 "digits" that indicate the "Minutes" (no 28 fig. 1)
and set the desired value.
• During the cooking cycle the display alternately shows: for 4
seconds, the value of the time set for the active step, and for
4 seconds the value of the total time remaining ("countdown")
for the rest of the other steps. In case "INFINITE time" is set,
the display shows alternately: for 4 seconds, the "InF" value,
and for 4 seconds the elapsed time value.
• The value of the TIME parameter ("Hours/Minutes") can also
be changed with the cooking cycle active.
Setting cooking STEPS:
• Each cooking cycle may consist of up to 10 STEPS. The oper-
ating parameters and the desired values can be set for each
step (chapter "Touch Screen control operation" on page 7).
• After setting the parameters and relative values for the first
step ("Phase 01"), the following ones ("Phase 02", "Phase 03"
...), can be set by touching the 2 "digits" indicating the num-
ber of the STEPS (no 29 fig. 1), and touching the symbol
• The desired operating parameter values must be set for each
step.
• During cooking, the display shows alternately: for 4 seconds,
the number of the active step, and for 4 seconds the maxi-
mum number of steps set.
Cooking TEMPERATURE setting:
• Touch the 3 "digits" indicating the TEMPERATURE (no 24 fig.
1) and set the desired value by touching the symbols
. Confirm the set value by touching the 3 "digits" of the
parameter or touching the symbol
• During the cooking cycle the display alternately shows: for 4
seconds, the temperature value set for the active step, and
for 4 seconds the value of the temperature measured inside
again.
(no 1 fig. 1). When the function is
. The PRE-HEATING tem-
, you can change this value from 10°C
. In the same way
.
or
.
or