Battery Status Indicator; Removing Or Sliding On The Titanium Sleeve; Reading The Serial Number; Using The Buttons - Servona digital XL Manual De Instrucciones

The battery holder of the SERVOX
aid is preassembled
Removing the battery holder:
 Screw off the bottom cover (E) anticlockwise, hol-
 Pull out the battery holder (H) straight
Figure (2) Removing the battery holder
Inserting batteries:
The battery poles are marked on the bottom of the
battery holder (H)
 Insert 4 fully charged AAA rechargeable batte-
Inserting the battery holder:
The battery holder has a fixing pin (I) on the top
Figure (3) Inserting the rechargeable batteries
side which is inserted into the pin hole provided inside
the speech aid and thus fixes the battery holder in the
correct position.
 Align the battery holder (H) with the fixing pin (I)
 Slide the battery holder (H) straight into the
Figure (4) Aligning and inserting the battery holder
 Then, put the bottom cover back on straight and

5.3 Battery status indicator

If the battery power decreases, the yellow LED light in
the volume control/battery status indicator (C) flashes.
If the battery power is no longer sufficient to maintain
the normal functions, the LED light is permanently lit and
no sound is produced.
 Replace batteries
Figure (5) Battery status indicator

5.4 Removing or sliding on the titanium sleeve

Caution
Risk of injury: The skin can be pinched when the titanium sleeve is slid off or on.
• Move the titanium sleeve slowly and carefully!
The titanium sleeve protects the electrical components of the SERVOX
the titanium sleeve there is also the type plate with the identification features of the speech aid and
the removable strap protector for attaching the carrying strap.
28 of 304
® digital XL speech
ding the titanium cover to prevent it from slipping
off the speech aid
ries/4 full AAA batteries into the battery holder
with the terminals aligned with the marking on
the battery holder base
on the left edge of the buttons as in figure 4 and
align the guide mark on the battery holder cen-
trally with the buttons
speech aid, slowly and without pressure, until the
fixing pin (I) slides into the pin hole
screw it on hand-tight
® digital XL speech aid. Under
Removing or sliding on the titanium
sleeve
 Screw off the bottom cover and re-
move the battery holder (H)
 Hold the speech aid by the screw cap
and pull the titanium cover down-
wards or push it on from below.
 Replace the battery holder and screw
the bottom cover back on
Figure (6) Titanium sleeve
Figure (8) Type plate with all identi- Figure (9) Strap protector for attaching the carrying strap
fication characteristics

5.5 Reading the serial number

The serial number is located on the type plate of the SERVOX
speech aid. To read the serial number, unscrew the bottom cover and
slide the titanium sleeve off the housing.
On the plastic housing underneath, the serial number is indicated on the
type plate behind the marking "SN".

5.6 Using the buttons

In natural speech, individual syllables, words or parts of sentences are
emphasised by a change in pitch. The SERVOX ®
assigned different pitches.
In the factory setting, the upper button (A) is preset in a lower audio frequency as the basic tone for
speaking and the lower button (B) in a higher audio frequency for emphasising individual syllables,
words or parts of sentences. The pitch of each button can be adjusted
individually.
 Hold button (A) to speak (basic tone)
 Briefly change to button (B) to emphasise individual language
elements
The buttons can be operated with the index and middle fingers or by
tilting the thumb (see Figure 13 and 14).
Figure (12) Control elements
Button A
Button B
Volume control
(wheel)
Figure (13) Operating the buttons by tilting the thumb
Figure (7) Bottom cover
Figure (10) 2 DIP switches for set-
ting the audio frequency
® digital XL
Figure (11) Serial number strap
digital XL speech aid therefore has 2 buttons that are
Figure (14) Operating the
buttons with the index and
middle finger
29 of 304
EN