Generac RD015 Manual Del Propietário página 27

Running Manual
Running-Utility Lost
Running-Remote Start
Running-2 Wire Start
Running - Exercise
Switched Off
Stopped - Auto
"Good" "Inspect Battery" or "Check Battery"
Stopped - Alarm
ENTER
- 1 thru 50 +
ESC
- 1 thru 50 +
ENTER
WARNING MESSAGE(S)
"Low Battery"
"Exercise Set Error"
"FIRMWARE ERROR-9"
"Schedule A Maint"
"Schedule B Maint"
"Schedule C Maint"
"Battery Problem"
"Charger Warning"
"Charger Missing AC"
Language
"Overload Warning"
ESC
"Overload Cooldown"
English
"SEEPROM ABUSE"
"USB Warning"
"Download Failure"
"Low Fuel (20%)"
"Stopping..."
ESC Current Date/Time
ALARM MESSAGE(S)*
9/12/13 12:22
"High Engine Temp."
"Low Oil Pressure"
"Overcrank"
"Overspeed"
"RPM Sense Loss"
"Underspeed"
Exercise Time
"Controller Fault"
ESC
"Ignition Fault Code"
14:00 Wednesday
"WIRING ERROR"
"Over Voltage"
"Under Voltage"
"Overload Remove Load"
Firmware Update*
"Canbus Error"
"Governor Fault"
Press Enter
"Missing Cam Pulse"
"Missing Crank Pulse"
"Ruptured Tank"
"Low Fuel (10%)"
Start up Delay (sec)
ESC
"E-Stop"
"Fuse Problem"
*Note: E-Codes Not Shown
Warmup Time (sec)
ESC
Owner's Manual for Stationary Diesel Generators
Home Screen
ENTER
Battery Condition
ENTER
ESC
ENTER
- Run Log +
"Run Log"
ENTER
ESC
ESC
"Alarm Log"
- Alarm Log +
ENTER
ENTER
Language Language
+
+ English - + Espanol -
-
ESC
Select Hour (0-23)
ENTER
- 14 +
ESC
Quiet Test Mode ?
ENTER ENTER
- YES or NO +
*NOTE: Any key other than Enter will
force you out of Firmware Update
Possible Message(s)
Firmware Update
ENTER
ESC Insert USB
Unsupported Device
2-1500
Default: 10s
5-1500
Default: 5s
Figure 4-3. Navigation Menu
Switched to "OFF"
Hours of Protection
Current Date/Time
0 (H)
02/14/13 07:40
ESC
ESC
SYSTEM DATE/TIME
ENTER
BATTERY SUB MENUS
Main Menu
ENTER ESC
HISTORY MAINT
EDIT DEALER
Access Requires Password
Language Language
+ +
+ Francais - + Portuguese -
- -
ESC
Select Month (1-12)
Select Min (0-59)
ENTER ENTER
- 0 + - 2 +
ESC ESC
Select Hour (0-23) Select Min (0-59)
ENTER
- 14 + - 0 +
ENTER
"Main V XXX To V XXX "
Corrupted File
Invalid File
"GUI V XXX To XXX"
File Not Found
Controller Fault
2.3L & 2.4L Units Only
- 5-30 +
Pre Heat
Default: 5s
ESC
Run Hours (H)
ESC
MAINT:
ESC
ENTER
Maint. Log Scheduled
ENTER ESC
ENTER
- 1 thru 50 +
"Schedule A Serviced"
"Schedule B Serviced"
"Schedule C Serviced"
"Maintenance Reset"
"Service Schedule A"
"Service Schedule B"
"Inspect Battery 200 RnHr or 12/27/13"
"Service Schedule C"
+
"Next Maintenance 200 RnHr or 12/27/13"
ESC
ESC
Select Date (1-31)
ENTER ENTER
- 13 +
ESC
ENTER
Select Day
ENTER
- Wednesday +
Select "Yes" then Press "Enter" to continue or Press
"ESCAPE" to escape out of updating.
"Are You Sure?"
When the controller powers up the very first screen
ESC "- Yes or No +"
displays the version number for a few seconds.
When update is complete remove Thumb Drive, then
follow the Install Wizard Menu.
Operation
Up Arrow = (+)
Down Arrow = (-)
0.0
ENTER
Run Hrs
ESC
EXAMPLE:
"Service Schedule A, B or C"
ESC
ENTER
Select Year (0-99)
- 13 +
21