Extraordinary Maintenance; Re-Start After Long Period Of Inactivity; How To Request After-Sales Assistance; Diagnostics - Zhermack alghamix II Traducción De Las Instrucciones De Servicio Originales

8.3

EXTRAORDINARY MAINTENANCE

Extraordinary maintenance includes the repair of any accidental breakage
and the replacement of worn or malfunctioning parts.
EN
All electrical and mechanical interventions must only be
performed by a Zhermack authorised maintenance technician.
Any modification that alters machine features from a safety and
risk-prevention point of view can only be carried out by the
Manufacturer who will then certify conformity of the machine
with safety standards. Therefore any modification or maintenance
intervention not considered in this manual is to be considered
prohibited. Any modification, tampering or repair performed by
unauthorised staff along with the use of non-original spare parts
relieve the Manufacturer from any liability. If the necessary
maintenance interventions are not considered in this Use and
Maintenance Manual, contact the Authorised After-Sales Centre.
8.4

RE-START AFTER LONG PERIOD OF INACTIVITY

If the machine is re-started after a particularly long period of inactivity,
operate as indicated in Chapter 6 regarding commissioning.
If the machine functions anomalously, act as described in Chapter 9
regarding "Diagnostics". if the problem should persist or is not considered,
contact the Authorised After-Sales Centre immediately.
8.5 HOW TO REQUEST TECHNICAL AFTER-SALES ASSISTANCE
Choose one of the following options to request after-sales assistance:
1. contact the Authorised After-Sales Centre;
2. telephone the Zhermack After-Sales Service at +39 0425.597.611 and
proceed as follows: give personal data (e.g. address and telephone
number); state the information given on the machine identification plate
(see paragraph 3.5); explain the problem with the machine clearly;
3. fax all of the information stated in the previous point and the correctly
filled-in identification form (see Attachment 10.2) to the following n° +39
0425.53.596.
CHAPTER 9: DIAGNOSTICS
9.1

GENERAL WARNINGS

If any of the anomalies described below should occur, solve the
problem, where allowed, with respect to all instructions
contained in this manual. If the problem persists, contact the
Authorised After-Sales Centre.
9.2

TROUBLESHOOTING

FAULT By activating the master switch in the "slow" and "fast"
position the bowl does not turn.
CAUSE 1. The plug is not inserted correctly.
2. The fuse is burned out.
REMEDY 1. Connect the electric power supply plug correctly.
2. Replace the fuse with one having the same features (F 250V
2.5A).
3. Contact the Authorised After-Sales Centre.
The reference figures are present on pages 3, 4 and 5 of this manual and in the product Quick Guide.
20
CHAPTER 10: ATTACHMENTS
10.1

EC DECLARATION OF CONFORMITY

The Manufacturer:
Zhermack S.p.A.
Via Bovazecchino, 100
45021 Badia Polesine • RO • Italy
Tel. +39 0425 597611 • Fax +39 0425 53596
Person authorised to compile the technical file:
Zhermack S.p.A.
Via Bovazecchino, 100
45021 Badia Polesine • RO • Italy
Tel. +39 0425 597611 • Fax +39 0425 53596
declares under its sole responsibility that the product:
alghamix II
is in conformity with Directive 2011/65 EU of the European Parliament
and of the Council of 8 June 2011 on the restriction of the use of certain
hazardous substances in electrical and electronic equipment.
It is also in conformity with the laws implementing the following directives:
EC Directive 2004/108 EC (EMC Directive) and subsequent amendments.
EC Directive 2006/95 (Low Voltage Directive) and subsequent amendments.
Please note that the manufacturer's liability for damages caused by a
defective product expires 10 years from the date on which the manufacturer
released such product on the market and that such liability is transferred to
the user in accordance with Directive 85/374/EEC, subsequent amendments
and the laws implementing it.
Badia Polesine, 25/02/14
Paolo Ambrosini
General Manager
alghamix II