The cleaning results are unsatisfacto-
ry
The brushes do not rotate
The optional all-round light and/or the
working light do not light up
Error K1/109
The device does not sweep properly 1. Check the roller brush and the side brushes for wear, replace if necessary.
The sweeping mechanism creates a
dust cloud
The cleaning result when sweeping in
the edge area is unsatisfactory
General
Travel speed (max.)
Transport speed
Reverse speed
Permissible braking distance on level ground at max.
travel speed of 10 km/h
Application time depending on brush head, brush con-
tact pressure and roughness of the ground
Theoretical surface coverage
Theoretical surface coverage with side scrubbing deck m
Theoretical surface coverage with 2 side brushes
Practical surface coverage with brush head
Fresh/waste water tank volume
Coarse dirt container capacity
Detergent tank (Dose option)
Detergent dosing range (from - to)
Minimum water dosing quantity
Maximum water dosing quantity
Max. surface pressure (incl. driver, water)
Device performance data
Nominal voltage
Battery capacity
Mean power input
Driving motor power
Suction motor power
Brush motor power
Charging time with empty battery
Brush roller drive power
Side brushes power (option)
Sweeping mechanism suction turbine power
Vacuuming
Suction performance, air quantity
Suction performance, vacuum
Filter area of dust filter
Vacuum turbine/suction bar
Cleaning brushes
Brush diameter
Brush length
Brush speed
Side scrubbing deck brush speed
Side scrubbing deck brush diameter
26
1. Set the appropriate cleaning program for the cleaning task.
2. Use suitable brushes for the cleaning task.
3. Use a suitable detergent for the cleaning task.
4. Reduce the driving speed.
5. Adjust the contact pressure.
6. Adjust the squeegee blades.
7. Check the brushes for wear and replace if necessary.
8. Check the water output.
1. Reduce the contact pressure.
2. Check if the brushes are blocked by a foreign body and remove the foreign body if necessary.
1. Check fuse F3, replace if necessary, (see chapter Replacing fuses).
1. Switch off the device.
2. Wait one minute.
3. Switch the device on again.
Additional malfunctions on the Combo variant
2. If the roller brush does not turn, check the drive belt, clean if necessary.
3. Check the function of the coarse dirt flap.
4. Check the sealing strips for wear, adjust or replace if necessary.
1. Empty the waste container.
2. Check the drive belts for the sweeping mechanism suction turbine.
3. Check the sealing sleeve on the suction fan.
4. Check the dust filter, clean or replace if necessary.
5. Check the filter box seal.
6. Check the sealing strip for wear, adjust or replace if necessary.
1. Check the height adjustment of the side brushes, adjust if necessary.
2. Replace the side brushes.
Technical data
B 260 RI
(R100)
km/h
10
km/h
10
km/h
6
m
1,9
h
5
2
m
/h
10000
2
/h
11200
2
m
/h
11500
2
m
/h
7000
l
260
l
26
l
10
%
0-3
l/min
0,9
l/min
9
2
N/mm
1,33
V
36
Ah
630
W
7500
W
2200
W
2x840
W
2x 1100
h
10
W
---
W
110
W
---
l/s
28 x 2
kPa (mbar)
14 (140)
2
m
---
kPa (mbar)
22/11 (220/110) 22/11 (220/110) 22/11 (220/110) 22/11 (220/110) 22/11 (220/110) 22/11 (220/110)
mm
160
mm
914
1/min
1250
1/min
140
mm
300
B 260 RI
B 260 RI
Combo (R100)
(R 120)
10
10
10
10
6
6
1,9
1,9
4,5
5
10000
12000
---
---
11500
13400
7000
8400
260
260
26
32
10
10
0-3
0-3
0,9
0,9
9
9
1,33
1,33
36
36
630
630
8900
7500
2200
2200
2x840
2x840
2x 1100
2x 1100
10
10
600
---
110
110
600
---
28 x 2
28 x 2
14 (140)
14 (140)
4
---
160
160
914
1118
1250
1250
---
---
---
---
English
B 260 RI
B 260 RI
B 260 RI
Combo (R 120)
(D100)
Combo (D100)
10
10
10
10
10
10
6
6
6
1,9
1,9
1,9
4,5
5
4,5
12000
10000
10000
---
11200
---
13400
11500
11500
8400
7000
7000
260
260
260
32
---
---
10
10
10
0-3
0-3
0-3
0,9
0,9
0,9
9
9
9
1,33
1,33
1,33
36
36
36
630
630
630
8900
7500
8900
2200
2200
2200
2x840
2x840
2x840
2x 1100
2x 1100
2x 1100
10
10
10
600
---
600
110
110
110
600
---
600
28 x 2
28 x 2
28 x 2
14 (140)
14 (140)
14 (140)
4
---
4
160
510
510
1118
---
---
1250
140
140
---
140
---
---
300
---