Siemens SINAMICS DCM Manual página 837

Tec_ctrl set1 scal
0.00...100.00 [%]
p2255 (100.00)
Tec_ctrl setp 1
p2253[C]
(0)
Tec_ctrl t_ramp-up
0.00...650.00 [s]
Tec_ctrl set2 scal
p2257 (1.00)
0.00...100.00 [%]
p2256 (100.00)
Tec_ctrl setp 2
+
p2254[C]
(0)
+
Tec_ctrl t_ramp-dn
0.00...650.00 [s]
Tec_ctrl I_lim act
-200.00...200.00 [%] -200.00...200.00 [%]
p2268 (-200.00)
0
0 1
Tec_ctrl config
1 = Actual value limit
p2252.3
Tec_ctrl act T
0.000...60.000 [s]
p2265 (0.000)
Tec_ctrl act val
p2264[C]
(0)
Tec_ctrl act aftFlt [%]
r2266
<1> P, I and D components can be disabled by entering a zero.
<2> Behavior can be changed via p2252.
<3> I component stop, only when r2273 and r2294 in same direction.
<101> The pre-assignment of the sampling time in p0115[6] is 4000.00 s.
1 2
DO: DC_CTRL
Technology controller - Control (r0108.16 = 1)
Tec_ctrl config
RU/RD indep setp sign
p2252.0
Tec_ctrl set T
0.00...60.00 [s]
p2261 (0.00)
<2>
1 = Integrator independent of Kp
+
Tec_ctrl set aftFlt [%]
r2262
Tec_ctrl set aftRFG [%]
p2258 (1.00)
r2260
Tec_ctrl u_lim act
p2267 (200.00)
0
0 1
Tech_ctrl gain act Tec_ctr ActVal fct
0.00...500.00 [%] 0...3
p2269 (100.00) p2270 (0)
Tech_ctrl act inv
0...1
p2271 (0)
-1
F07426
"Technology controller actual value limited"
3 4
Tec_ctrl Kp
0.000...1000.000
<1> <1>
p2280 (1.000)
Tec_ctr integ hold
p2286[C]
<3>
(0)
<2>
Tec_ctrl config
p2252.1
+
+ +
Tec_ctr prectr_sig
Tec_ctrl sys_dev [%]
r2273
p2263 = 0
Tec_ctrl sys_dev [%]
r2273
Tec_ctrl max_lim
p2263 = 1
-200.00...200.00 [%]
p2291 (100.00)
Tec_ctrl type
0 = D comp in act_val signal
1 = D comp in sys_deviation
p2263 (0)
Tec_ctrl D comp T
0.000...60.000 [s]
p2274 (0.000)
1 = Output signal without ramp active
<1>
1
d
Tec_ctrl min_lim
dt
-200.00...200.00 [%]
0
Tec_ctrl act scal [%]
r2272
Tec_ctrl enable
p2200[C]
(0)
5
fp_7958_13_eng.vsd
27.08.18 V01.05.00
p0115[6] (Drive Object)
Tec_ctrl Tn
0.000...60.000 [s]
p2285 (0.000)
Tec_ctrl outp scal
p2296[C]
Tec_ctrl outp scal
-100.00...100.00 [%] p2295
p2295 (100.00)
+
+
< 0
Technology controller limited
p2289[C]
(0) r2349.1
Tec_ctrMaxLimS_src
p2297[C]
p2291 (2291)
+
–
Tec_ctrl config
p2252.2
Tec_ctrl lim offs
p2299[C]
p2292 (0.00)
(0)
Tec_ctrl min_l s_s
–
p2298[C]
p2292 (2292)
+
Technology controller deactivated
1
r2349.0
6 7
Function diagram
SINAMICS DCM
<101>
(2295)
Tec_ctrl outp_sig [%]
r2294
Output negative
r2349.7
<2>
<2>
Tec_ctr t_RU/RD
0.00...100.00 [s]
p2293 (1.00)
8
- 7958 -