DeWalt DCM565 Traducido De Las Instrucciones Originales página 35

IMPORTanT: The chain cutters will dull immediately if they
touch the ground, stones, masonry or a nail while cutting.
To get the best possible performance from your chain saw it is
important to keep the teeth
sharpening services are available from your nearest D
service centre.
nOTE: Each time the saw chain is sharpened, it loses some of
the reduced kickback qualities and extra caution should be used.
It is recommended that a saw chain be sharpened no more than
four times.
Lubrication
Your power tool requires no additional lubrication.
Cleaning

WARNING: Electrical shock and mechanical hazard.
Disconnect the electrical appliance from the power source
before cleaning.

WARNING: To ensure safe and efficient operation, always
keep the electrical appliance and the ventilation slots clean.

WARNING: Never use solvents or other harsh chemicals for
cleaning the non-metallic parts of the tool. These chemicals may
weaken the materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
Ventilation slots can be cleaned using a dry, soft non-metallic
brush and/or a suitable vacuum cleaner. Do not use water or
any cleaning solutions. Wear approved eye protection and an
approved dust mask.
Optional Accessories

WARNING: Since accessories, other than those offered by
D WALT, have not been tested with this product, use of such
e
accessories with this tool could be hazardous. To reduce the risk
of injury, only D WALT-recommended accessories should be used
e
with this product.
Consult your dealer for further information on the
appropriate accessories.
Protecting the Environment
Separate collection. Products and batteries marked
w
with this symbol must not be disposed of with normal
household waste.
Products and batteries contain materials that can be
recovered or recycled, reducing the demand for raw materials.
Please recycle electrical products and batteries according to local
provisions. Further information is available at www.2helpU.com.
Rechargeable Battery Pack
This long-life battery pack must be recharged when it fails to
produce sufficient power on jobs that were easily done before. At the
end of its technical life, discard it with due care for our environment:
• Run the battery pack down completely, then remove it from
the tool.
• Li-Ion cells are recyclable. Take them to your dealer or a local
recycling station. The collected battery packs will be recycled or
disposed of properly.
of the saw chain sharp. Chain
21
WALT
e
DCM565 TROUBLESHOOTING
Problem Solution
Unit will not start. • Check battery installation.
• Check battery charging requirements.
• Check that lock-off is fully pushed
down prior to moving main trigger.
Unit shuts down • Charge battery.
in use.
• Unit is being forced. Restart and apply
less pressure.
Battery • Insert battery into charger until red
won't charge. charging light illuminates. Charge up to
8 hours if battery is totally drained.
• Plug charger into a working outlet.
• Check current at receptacle by
plugging in an appliance.
• Check to see if receptacle is connected
to a light switch which turns power off
when you turn out the lights.
• Move charger and appliance to a
surrounding air temperature of above
4.5 °C or below 40.5 °C.
Bar / • Refer to Adjusting Chain
Chain overheated. Tension section.
• Refer to Saw Chain and Guide Bar
Oiling section.
Chain is loose. • Refer to Adjusting Chain
Tension section.
Poor cut quality. • Refer to Adjusting Chain
Tension section. nOTE: Excessive
tension leads to excessive wear and
reduction in life of bar and chain.
Lubricate before each cut. Refer to
Replacing the Saw Chain section.
Unit runs but does • Chain could be installed backwards.
not cut. Refer to sections for installing and
removing chain.
Unit does not oil. • Refill oil reservoir.
• Clean guide bar, sprocket and sprocket
cover. Refer to Maintenance section.
EnGLIsh
35