Publicidad
Idiomas disponibles
Idiomas disponibles
Setting of influence function
Function, DI1 (CU 352) - DI3, [10, 12, 14]
Date and time
4.5.3
Temperature
Password
4.5.4
Power
Ethernet
4.5.5
Energy
GENIbus number
4.5.6
Software status
4.5.9
Alternative setpoints 2-7
External setpoint influence
Input value to be influenced by
4.1.3.2
Proportional pressure
S-system configuration
Min. time between start/stop
Max. number of starts/hour
Forced pump changeover
Pump start and stop speed
Compensation for pump start-up time
Stop parameters
Soft pressure build-up
Function, DI1 (IO 351-41) - DI9, [10-46]
Function, DI1 (IO 351-42) - DI9, [10-46]
Setting, AI1 (CU 352), [51] - AI3, [51, 54, 57]
Function, AI1 (CU 352) - AI3 [51, 54, 57]
Setting, AI1 (IO 351-41), [57] - AI2 [57, 60]
Function, AI1 (IO 351-41) - AI2 [57, 60]
Setting, AI1 (IO 351-42), [57] - AI2 [57, 60]
Function, AI1 (IO 351-42) - A2 [57, 60]
DO1 (CU 352), [71] is signalling - DO2 [71, 74]
DO1 (IO 351-41), [77] is signalling - DO7 [77-88]
DO1 (IO 351-42), [77] is signalling - DO7 [77-88]
AO1 (IO 351-41) [18] - AO3 [18, 22, 26]
AO1 (IO 351-42) [18] - AO3 [18, 22, 26]
[12 ,10] DI2 - [10] ,(IO 351-41)
[12 ,10] DI2 - [10] ,(IO 351-42)
Min., max. and user-defined duty
Min. duty
Max. duty
Set user-defined duty
Pilot pump curve data
Flow estimation
Customisable measured value type
Dry-running protection
Pressure/level switch
Measurement, inlet pressure
Measurement, tank level
Pumps outside duty range
Fault, feedback sensor
Change language to the service language (English)
Pressure
Differential pressure
Head
4.5.2.8
Level
4.5.2.9
Flow rate
4.5.2.10
Volume
Specific energy
4. Settings
Primary controller
4.1
PI controller
4.1.1
Alternative setpoints
4.1.2
4.1.2.1
4.1.3
4.1.3.1
Primary sensor
4.1.4
Secondary sensor
4.1.5
Clock program
4.1.6
4.1.7
4.1.8
Setpoint ramp
4.1.9
Pump cascade control
4.2
4.2.1
Standby pumps
4.2.3
4.2.4
Pump test run
4.2.5
Pump stop attempt
4.2.7
4.2.8
Min. performance
4.2.9
4.2.10
Secondary functions
4.3
Stop function
4.3.1
4.3.1.1
Pilot pump
4.3.2
4.3.3
Emergency run
4.3.5
Digital inputs
4.3.7
Analog inputs
4.3.8
Digital outputs
4.3.9
Analog outputs
4.3.10
Counter inputs
4.3.11
DI1
،ﻋ ﺩﺍﺩ ﺍﻟﺣﺟ ﻡ
DI1
،ﻋ ﺩﺍﺩ ﺍﻟﺣﺟ ﻡ
4.3.14
4.3.14.1
4.3.14.2
4.3.14.3
4.3.18
Pump curve data
4.3.19
4.3.23
Control source
4.3.20
Fixed inlet pressure
4.3.22
Flow estimation
4.3.23
Reduced operation
4.3.24
Multisensor settings
4.3.25
Differential sensor
4.3.27
4.3.28
Monitoring functions
4.4
4.4.1
4.4.1.1
4.4.1.2
4.4.1.3
Min. pressure
4.4.2
Max. pressure
4.4.3
External fault
4.4.4
Limit 1 exceeded
4.4.5
Limit 2 exceeded
4.4.6
4.4.7
Pressure relief
4.4.8
Log values
4.4.9
4.4.10
Non-return valve
4.4.11
Functions, CU 352
4.5
Run wizard again
Display language
4.5.1
Units
4.5.2
4.5.2.1
4.5.2.2
4.5.2.3
4.5.2.4
4.5.2.5
4.5.2.6
4.5.2.7
Status display menu
4.6
461
ﻳ ُﺗﺑ ﻊ ﻣ ﻥ ﺍﻟﺻ ﻔﺣﺔ
1 ->
513
Publicidad
