Descargar Imprimir esta página

SILKO ALI 700 Serie Instrucciones Para Instalación, Uso Y Mantenimiento página 55

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 79
GENERAL INFORMATION
This chapter contains general information which all users of the
users of the manual is provided in subsequent chapters (" IN-
STRUCTIONS FOR .... " ).
1 APPLIANCE SPECIFICATIONS
• The appliance data plate is located inside the control panel.
• The appliance model and serial number are detailed on de-
cals and on the packaging.
2 GENERAL PRESCRIPTIONS
The manufacturer will not be liable for
any damage or injury resulting from fai-
lure to observe the following rules.
REMINDERS FOR THE INSTALLER
• Read this manual carefully. It provides important information
for safe installation, use and maintenance of the appliance.
authorized by the manufacturer, in compliance with current
safety standards and the instructions given in this manual.
• The appliance must be installed in a well-ventilated room.
detailed on the packaging and on the appliance data plate.
• Do not obstruct any air vents or drains present on the ap-
pliance.
• Do not tamper with appliance components.
• This type of appliance is intended for commercial applica-
tions: kitchens of restaurants, canteens, hospitals, and
shops such as bakeries, butchers and similar. It is howe-
ver not intended for continuous mass food production.
WARNING: Opening the drain valve will cause the hot
• Before pouring in oil make sure that there is no water in the
well.
• An upstream installation on all appliances working LPG ga-
ses (G30 and/or G31) of a gas pressure regulator to stop
potential gas overpressures is required (OPSO).
REMINDERS FOR THE MAINTENANCE TECHNICIAN
• Read this manual carefully. It provides important information
for safe installation, use and maintenance of the appliance.
authorized by the manufacturer, in compliance with current
safety standards and the instructions given in this manual.
detailed on the packaging and on the appliance data plate.
• The appliance must be installed in a well-ventilated room.
• Do not obstruct any air vents or drains present on the ap-
pliance.
• Do not tamper with appliance components.
REMINDERS FOR CLEANING
• Clean the external satin stainless steel surfaces, the inside of
the cooking tanks and the cooking plates daily.
• The internal appliance components must be cleaned by a
specialist technician at least twice a year.
• Do not clean the appliance with high pressure water jets or
steam cleaners.
base underneath the appliance.
in the dishwasher.
3 SAFETY AND CONTROL DEVICES
SAFETY THERMOSTAT
The manufacturer will not be liable for any damage or in-
jury resulting from failure to observe the following rules.
• The appliance is equipped with a manual reset safety ther-
mostat which interrupts heating when the operating tempera-
ture exceeds the maximum permitted value.
• To restore appliance operation, open the door and press the
thermostat reset button. This procedure may only be carried
4 DISPOSAL OF PACKAGING AND THE APPLIANCE
PACKAGING
The packaging is made using environmentally friendly mate-
rials. The plastic recyclable components are:
-
• the transparent cover, the bags containing the instructions
manual and nozzles ( made of polyethylene - PE.).
• the straps (in polypropylene - PP).
APPLIANCE
The appliance is manufactured 90% from recyclable metals
(stainless steel, aluminum sheet, copper.... ).
The appliance must be scrapped in compliance with current
regulations governing such disposal.
• It must be disposed of properly.
• Make the appliance unusable before scrapping.
5 RISKS DUE TO NOISE
• As regards airborne acoustical noise emissions, the A-
weighted sound pressure level is below 70 dB(A).
INSTRUCTIONS FOR INSTALLATION
REMINDERS FOR THE INSTALLER
The manufacturer will not be liable for any damage or in-
jury resulting from failure to observe the following rules.
• Read this manual carefully. It provides important information
for safe installation, use and maintenance of the appliance.
-
authorized by the manufacturer, in compliance with current
safety standards and the instructions given in this manual.
detailed on the packaging and on the appliance data plate.
• The appliance must be installed in a well-ventilated room.
• Do not obstruct any air vents or drains present on the ap-
pliance.
• Do not tamper with appliance components.
• An upstream installation on all appliances working LPG ga-
ses (G30 and/or G31) of a gas pressure regulator to stop
potential gas overpressures is required (OPSO).
6 REFERENCE STANDARDS AND LAWS
Install the appliance in compliance with current safety regula-
tions.
-
5

Publicidad

loading

Este manual también es adecuado para:

900 serie