Publicidad
Idiomas disponibles
Idiomas disponibles
Occurs for a malfunction or incorrect connection of the sensor.
It is indicated on the display by the message "Pr1" alternating
with the normal view, by the lighting of the Alarm led and the
buzzer. Heating is excluded for safety reasons. This alarm re-
• Board temperature sensor error alarm
Occurs for a malfunction of the sensor on the electronic board.
It is indicated on the display by the message "Pr1" alternating
with the normal view, by the lighting of the Alarm led and the
buzzer. Heating is excluded for safety reasons. This alarm re-
• Board temperature alarm
Occurs for abnormal heating of the electronic board. It is indi-
cated on the display by the message "Ht" alternating with the
normal view, by the lighting of the Alarm led and the buzzer,
which may be silenced by pressing any button. Instead the
message "Ht" disappears only if the temperature returns within
the established parameters. Even though the appliance will
continue to operate, if this alarm occurs it is recommended to
• Oil temperature alarm
Occurs if the oil reaches a temperature that is too high in com-
parison with the established set point. It is indicated on the di-
splay by the message "AL" alternating with the normal view,
by the lighting of the Alarm led and the buzzer, which may be
silenced by pressing any button. Instead the message "AL" di-
sappears only if the temperature returns within the established
parameters. Even though the appliance will continue to opera-
te, if this alarm occurs it is recommended to have it checked
The leds light up depending on the operating phases, as indi-
cated below:
L1
Mode A (preheating)
Mode B (holding)
Mode C (adjustment)
L2
Mode A (preheating)
Mode B (holding)
Mode C (adjustment)
L3
Setting the set point
Display of set point with
button 5
14 PROLONGED DISUSE
Before any prolonged disuse of the appliance, proceed as fol-
lows:
• Clean the appliance thoroughly.
• Rub stainless steel surfaces with a cloth soaked in Vaseline
Blinking
Lit
with
temperature
between 100 +/- 5°C. Blin-
king with temperature out-
side the range 100 +/- 5°C
for over 20 seconds.
Lit if the temperature after
reaching the set point is
between the set-point +/-
5°C. Blinking until the set
point is reached and then if
the temperature is outside
the range set point +/- 5°C
for over 20 seconds.
Blinking
Lit
Blinking
Lit
• Leave lids open.
•
the main switch.
Following prolonged disuse, proceed as follows:
• Inspect the appliance thoroughly before using it again.
• Allow electric appliances to operate at the lowest temperatu-
re for at least 60 minutes.
INSTRUCTIONS FOR CLEANING
REMINDERS FOR CLEANING
The manufacturer will not be liable for any damage or in-
jury resulting from failure to observe the following rules.
• Disconnect the appliance electrical power supply, if present,
before proceeding with any operation.
• Clean the external satin stainless steel surfaces, the inside of
the cooking tanks and the cooking plates daily.
• The internal appliance components must be cleaned by a
specialist technician at least twice a year.
• Do not clean the appliance with high pressure water jets or
steam cleaners.
•
base underneath the appliance.
•
in the dishwasher.
•
SATIN FINISH STAINLESS STEEL SURFACES
• Clean the surfaces with a cloth or sponge using water and
proprietary non-abrasive detergents. Follow the grain of the
• Do not use pan scourers or other iron items.
• Do not use chemical products containing chlorine.
• Do not use sharp objects which might scratch and damage
the surfaces.
COOKING TANKS
• Clean the tanks by bringing the water to the boil, with the
addition of grease remover detergent if necessary.
• Remove any limescale deposits with a proprietary limescale
remover.
FILTERS
reused, guarantees better cooking of the food. To clean the
a degreasing soap, rinse and dry When the procedure is con-
must be renewed
INSTRUCTIONS FOR MAINTENANCE
REMINDERS FOR THE MAINTENANCE TECHNICIAN
The manufacturer will not be liable for any damage or in-
jury resulting from failure to observe the following rules.
• Read this manual carefully. It provides important information
for safe installation, use and maintenance of the appliance.
• Disconnect the appliance electrical power supply, if present,
before proceeding with any operation.
•
authorized by the manufacturer, in compliance with current
safety standards and the instructions given in this manual.
-
11
Publicidad
