Publicidad
Idiomas disponibles
Idiomas disponibles
ELECTRONIC ELECTRIC FRYERS (WITH ENCODER)
The main switch has the following positions:
1 Fryer on
Switching on the fryer
•
45°.The whole display lights up for a few seconds, then
shows the temperature measured in the well. Temperature
adjustment is not active.
• Turn the thermostat knob to position "0".
•
OPERATION OF ELECTRONIC THERMOSTAT(WITH EN-
CODER)
Fig.B
The temperature may be adjusted in three operating modes:
• (A) Preheating: for melting solid fats. Heating takes place
cyclically at predetermined times so as to avoid sudden in-
creases in temperature. This phase ends automatically the
in the well.
• (B) Holding: the temperature is adjusted and kept at the pre-
determined value (100°C).
• (C) Main adjustment: the temperature is adjusted and kept at
is reached may be indicated by the buzzer.
Setting the set point
• Press and release the knob 2. The display shows the value of
the current set point.
• Turn the knob 2 to the desired value.
•
leasing it (or do not act for 15 seconds). The display again
shows the temperature in the well.
Pressing the buttons
•
buttons 3-4-5-6 are pressed and immediately released, or
held down for at least 1 second.
Activating the heating
• Press button 3 (for 1 sec.). The appliance is set so that it
starts in mode C, that is performing the adjustment according
to the established set point.
Activating preheating (melting)
• Press button 4 (for 1 sec.), bearing in mind that:
• if the temperature in the well is lower than the set value
(100°C), preheating (mode A) starts until the appliance pas-
ses to holding (mode B).
• if the temperature in the well is higher than the set value
(100°C), the appliance immediately passes to holding (mode
B).
To return to mode C
• Press button 4 (for 1 sec.).
10
To stop heating
• Press button 3 (for 1 sec.).
Timer characteristics
NB:
on the adjustment and operation of the thermostat.
The timer value may be set between 0 and 99 minutes. Set-
ting the value at 0 means excluding the timer. The time is ex-
pressed in minutes. A few seconds before the timer returns to
zero the buzzer starts to sound and the display automatically
shows the remaining time in seconds. Shortly after the end of
the countdown the buzzer stops and the display again shows
the temperature in the well.
Setting the timer
•
• 2. Press and immediately release button 6. The correct set-
ting appears blinking on the display. The message "min" blin-
ks too.
• 3. Turn the knob 2 to the desired value.
•
for 15 sec.). The display again shows the temperature in the
well.
Starting the countdown
• Press button 6 (for 1 sec.). The message"min" blinks and the
display continues showing the temperature in the well.
Stopping the countdown
•
timer stops and the initial value is reset.
Changing the countdown
• It is possible to change a countdown in progress (message
"min" blinking) by performing steps 2-3-4. The countdown
starts again from the new set value but this value is not me-
morized: the next countdown will start with the previous va-
lue.
Silencing the buzzer.
-
To silence the buzzer press any button or knob 2. The buzzer
will sound for:
• Sensor error (*)
• Board temperature alarm (*)
• Temperature alarm
•
• At the end of the timer countdown
assistance.
Choosing the value shown on the display
Usually the display shows the temperature value in the well.
By pressing button 5 (for 1 sec.), the display will show in se-
quence:
• The current set point if led L3 is lit
• The timer if the message "min" is lit
NB: If button 5 is pressed and immediately released the display
shows the message (Pbb): this message is reserved for the
manufacturer. To quit, press and immediately release button 5.
Alarms
The thermostat manages the following alarms:
• Adjustment sensor error alarm
Publicidad
