Command Interface Symbols - Sammic ABS-15/2 Instrucciones De Uso

4 COMMAND INTERFACE SYMBOLS

24 23
1 2 3 4 5 6
Capacitive Interface
1 - Stand-by Button
Standby button, if pressed for more than 3 seconds it takes the
card into standby or switches it on again
2 - Positive Chilling Button
used to select the mode of positive chilling
3 - Negative Chilling Button
used to select the mode of negative chilling
4 - Chill� LED Temperature
Led on means that the chilling is via Temperature mode (insert
probe)
5 - Chilling mode button
A button that selects the mode of chilling with Time or Temperature
(insert probe use); the selected mode is represented by ignition of
one of the two LEDs located on the right and left of the button and
they are marked with the temperature or time symbol
6 - Chill� LED Time
Led on means that the chilling is via Time mode
7 - Decrease Button
Parameter or setting value decrease buttons (the "-" button allows
silencing of the beeper if active)
8 - Chilling Phase LED
Symbol representing the chilling phase (it flashes when at that
phase)
9 - Storage Phase LED
Symbol representing the chilling phase (it flashes when at that
phase)
10 - Ice-cream button
The ice-cream button if pressed once starts the ice-cream cycle
(see section 2.16), and if pressed for more than 3 seconds it starts
the ice-cream defrost cycle
11 - HACCP button
The HACCP button which starts the data reversal cycle onto USB
12 - Ozone Button
Button that starts the ozone sanitising cycle (if any)
13 - Defrost Button
Button that when pressed once starts drying with door open (see
section 2.5), while if pressed for at least 3 seconds it starts the
hot gas defrost cycle
14 - Status LED
RGB on mark lettering. The lettering assumes the following colours
depending on the following relative connected states:
BLUE - Phase of chilling, deep-freezing or storage
LIGHT BLUE - Defrost time
GREEN - Machine on stand by
WHITE - Machine at standstill
RED FLASHING - Serious alarm
11
22 21 20 19
7 8
18 17
ICE CREAM HACCP
9 10 11
FLASHING YELLOW - Non serious alarm (door opening - main-
tenance -1° kriwan intervention)
15 - Thawing Button
Button that when pressed starts the defrost cycle
16 - Program Button
Programs recall or storage button
17 - Temperature Symbol
The symbol lights up when a cycle is active and the cell tempera-
ture (Time chilling) or Product temperature (Temperature chilling)
is detected. In the second case the product probe is shown with
the highest value. With the cycle in progress press the button (12)
to display in sequence the values of the insert probe 1 and 2 and
of the evaporator sensor probe in flashing mode and the display
(19) will show the letters in sequence SP1+"probe value",SP2+
"probe value" and SE+ "value
18 - Display- Temperature
Second part of the alphanumeric display (last 4 digits) for repre-
sentation of the T° cell or T° product and evaporator value
19 - Display- Time
First part of the alphanumeric display (first 4 digits) for representa-
tion of the time value remaining of chilling
20 - Time Symbol
The symbol lights up when the cycle is running; the time remain-
ing will be displayed. If the button (5) is pressed the elapsed time
will flash for 5 seconds (both for Time and Temperature chilling)
21 - Increase Button
Parameter or setting value increase buttons
22 - Cycles Start/Stop Button
Start/Stop button to start/stop the chilling cycle set; with a cycle
started, the button remains lit
23 - Negative Chilling LED
The number of LEDs lit indicates the intensity of the negative
chilling (increments by pressing the button (2))
24 - Positive Chilling LED
The number of LEDs lit indicates the intensity of the positive chill-
ing (increments by pressing the button (1))
16 15 14
THAW
PROGRAM
O
3
OZONE
AIR
12 13
71503136-0-R000