Ozonator; Ice-Cream Cycle - Sammic ABS-15/2 Instrucciones De Uso

and the beeper emits beeps.
When closing the door, the fan starts without delays.
If the machine is running the door remains open for more
than 5 minutes, the fan does NOT start again. The com-
pressor is also locked and the open door alarm is given.
Door reclosing, resetting of the audible alarm, visual and
alarm relay.
If the door is opened while the machine is in "stop" the
beeper does not sound but the appearance of the wording
DOOR OPEN continues.

11 OZONATOR

This function is only available when the machine is stopped
and is activated by pressing the ozonation button (12) (the
LED of the button comes on). The ozone is released for 120
minutes after which the release ends (the LED goes off).
At the same time as the Ozonator the fan is also activated
to facilitate movement.
During the sterilisation cycle the word "Ozone" will flash on
the display (18) and the display (19) will show the count-
down of the cycle time. If the door is opened during the 120
minutes, the sterilisation cycle will stop IMMEDIATELY; it
will not even start upon closing of the door, and the scroll-
ing text "STOP Ozone Cycle" will appear for 5 seconds. If
the ozonator is not installed the scrolling text "Ozone Not
Present - Ozono non presente" will appear on the display
for 10 seconds.

12 ICE-CREAM CYCLE

This cycle enables the user to use the chiller in negative
chiller mode with a Timer that schedules the introduction and
extraction of ice-cream containers, allowing the surfaces
to harden, after leaving the ice-cream making machine.
With the machine in stop mode, press the "ice-cream" but-
ton (10); the beeper will emit a beep and the LED of the
button will start to flash. The negative chilling cycle will start
immediately (to cool the machine), the display (19) of the
time will show the flashing cycle time while the display (18)
will indicate the temperature of the cell probe.
The user has the option, at this point, to modify the time
of the hardening cycle by pressing the "+" and "-", and to
confirm the time by pressing the "ice-cream" button (10).
After this setting when the user opens the door (to introduce
the ice-cream) and then recloses it, a beep is emitted as
confirmation and the countdown will start. When the time
reaches zero, the beeper will sound for 60 seconds, and
the sliding text "carica gelato - charge ice cream" will ap-
pear. Then whenever the door is closed, any countdown in
progress is interrupted and a new one starts.
During the cycle the user may at any time change the time
15
and the temperature Set as default as follows:
1) by pressing the "ice-cream" button (10), with the first
time press the time on the display (19) will flash and it can
be changed with the buttons +/-.
2) the next press of the button (10) will acquire the new
value.
3) now using the buttons +/- it is possible to change the
flashing set represented on the display 1(8) with a value
that can range from the minimum value to a maximum one
(this theoretically allows setting of the long softening cycles
for ice-cream which, extracted from the storage machine,
must be placed on display).
4) pressing the button (10) allows saving of the new value
followed by return to the cycle.
The user can stop this cycle at any time by pressing the
START/STOP button (22).
13 THAWING CYCLE
This function aims to safely thaw (below 10°C of tempera-
ture) cell) previously frozen or deep-frozen products. The
process is based both on cell temperature control, with a
positive value between 3°C and 10°C average, and on the
action of forced ventilation.
When the machine is stopped, select the thawing cycle by
pressing the button (15); the cycle will start immediately
showing on the "display 19" the standard thawing time and
on display 18" the measured cell temperature .
To change the values of time and temperature set, simply
press the button (15) until the display flashes which will
present the time value set. With the +/-buttons it is possible
to modify the thawing time. With the modification completed
with the +/-buttons it is possible to change the SET which
will be confirmed by pressing the button (5) or by waiting
5 seconds.
Then the temperature set value flashes on the display (8)
which can also be changed with the +/- buttons. With the
modification completed with the +/-buttons (6) it is possible
to change the SET by pressing the button (3) or by waiting
5 seconds.
Then on the display, if VE2 is different from 100, the word-
ing "HARD FANS" will be represented (if fan regulation is
enabled). To confirm press the button (5), while to change
press the +/- buttons until appearance of the second option
"SOFT FANS" (reduced evaporator fan speed); pressing the
button (5) the value selected is confirmed.
After this operation, the cycle in function is resumed which
when finished will activate the beeper and the scrolling text
71503136-0-R000