Blackmagic Design ATEM 1 M/E Manual De Instalación Y Funcionamiento página 23

Getting Started
23
CUT CUT CUT CUT DIP CUT CUT AUX 7 AUX 8 AUX 9 AUX 10 AUX 11 AUX 12 DEST
SHIFT
KEY 1 KEY 2 KEY 3 KEY 4 BORD STNG DVE AUX 1 AUX 2 AUX 3 AUX 4 AUX 5 AUX 6
SHIFT
Camera Camera Camera Camera Camera Camera Black Color Media Player Player Media Color Color Media Player Media Player
1 2 3 4 5 6 Bars 1 2 1 2 1 Key 2 Key
PLAYER
SHIFT
CUT CUT CUT CUT DIP CUT CUT CUT CUT CUT DEST
BOX 1 BOX 2 BOX 3 BOX 4 SHIFT
KEY 1 KEY 2 KEY 3 KEY 4 BORD STNG DVE DSK 1 DSK 2 SSRC
BKGD
SHIFT
Camera Camera Camera Camera Camera Camera Camera Camera Media Player Player Media Black Color Color Color Media Player Player Media DIP
1 2 3 4 5 6 7 8 1 2 Bars 1 2 1 Key 2 Key
MIX
PREV
TRANS
SHIFT
Change Network Settings from the System Control
Changing the Broadcast Panel Network Settings
ON ON ON ON
BKGD KEY 1 KEY 2 KEY 3 KEY 4 FTB
Because the broadcast panel is also on the network and communicating with the switcher, it also has
BOX 4
M/E 2 M/E 2
PATT KEY BOX 2
DIP
WIPE STNG DVE
MIX
M/E 1 M/E 1 BOX 4
PATT KEY
BOX 2
network settings so it can connect to the network. These settings are different to the switcher IP address,
TRANS EFFECTS DSK COLOR PREV
KEYS KEYS TRANS
MEDIA
PANEL CUT AUTO
SETUP
1 2 3 which is just where the panel is looking to find the switcher. The panel network settings can be changed by
4 5 6
7 8 9
ON ON ON ON
CAM 0 CLR
following the steps below:
KEY 1 KEY 2 KEY 3 KEY 4 FTB
DSK 1 DSK 2
TIE TIE
WIPE STNG DVE
Step 1. On the broadcast panel system control menus, select the NETWRK SETUP menu button.
EFFECTS DSK
TRANS KEYS KEYS COLOR
DSK 1 DSK 2
CUT CUT
AUX PLAYER MEDIA
DSK 1 DSK 2
CUT AUTO PANEL SETUP AUTO AUTO
Step 2. The broadcast panel's current IP address, net mask and gateway information is displayed.
Step 3. The next step is to decide if you want the panel to use a fixed IP address or to be automatically
Step 4. If you have elected to use a fixed IP address, you now need to set this IP address by selecting the
Step 5. If the subnet mask and gateway address need to be set, then select the relevant buttons on the
Step 6. When any settings have been changed, SAVE and REVERT menu buttons will become available.
If the broadcast panel has already established connection to the switcher, you can access the
NETWRK SETUP menu from the HOME menu by pressing the SHIFT and CUT/FILL buttons
simultaneously on the ATEM 1 M/E Broadcast Panel, or the SHIFT and DEST SHIFT buttons in
the M/E 1 block of the ATEM 2 M/E Broadcast Panel. This will reveal the NETWRK SETUP menu
button so you can select the network settings.
assigned an IP address from a DHCP server. Select PANEL DHCP to set this using the soft keys on
the main display.
If you're connecting direct to a switcher without a network, then you won't have a DHCP server
to assign an IP address automatically, so you will want to select fixed. ATEM Broadcast Panels are
delivered with a fixed IP address set to 192.168.10.10, for a direct connection.
However if your network has lots of computers that automatically assign IP addresses via DHCP,
then you can also select DHCP on the panel so the panel can get its network information
automatically. This is possible on the panel, and it's only the switcher itself that always requires a
fixed IP, as the switcher needs to be found by the control panels at a known fixed address on your
network.
If you select DHCP, your network settings will be complete because the panel network settings
will be obtained from the network automatically.
PANEL IP menu button and use the knobs or the numeric keypad to edit each field as required.
Changing this IP address may cause the panel to lose communication.
system control buttons to set and use knobs or the numeric keypad to edit.
Select SAVE to save the changes to the new network settings, or REVERT to ignore the changes
and revert to the current network settings.