Publicidad
Idiomas disponibles
Idiomas disponibles
KEY
KEY
KEY
2
3
4
CHROMA
PATTRN
DVE
KEY
KEY
HOME
Using the ATEM 1 M/E Broadcast Panel
50
KEY
KEY
KEY
KEY
1
2
3
4
1
2
3
4
5
6
LUMA
CHROMA
PATTRN
DVE
KEY
KEY
KEY
7
8
9
MASK
MENU
HOME
CAM
0
CLR
CUT
Control Panel
Main
ON
ON
ON
ON
FILL
Backup
Switcher
CUT
Main
BKGD
KEY 1
KEY 2
KEY 3
KEY 4
DSK 1
DSK 2
FILL
TIE
TIE
Backup
DIP
MIX
SHIFT
DSK 1
DSK 2
CUT
CUT
PREV
CUT
AUTO
DSK 1
DSK 2
FTB
TRANS
AUTO
AUTO
Transition Control and Upstream Keyers
SHIFT
PREV
TRANS
KEY
KEY
KEY
KEY
1
2
3
4
1
2
3
ON
ON
4
5
6
LUMA
CHROMA
PATTRN
DVE
KEY
KEY
KEY
7
8
9
MASK
MENU
HOME
CAM
0
CLR
CUT
Control Panel
BKGD
KEY 1
KEY 2
Main
ON
ON
ON
ON
Backup
FILL
Switcher
CUT
Main
BKGD
KEY 1
KEY 2
KEY 3
KEY 4
DSK 1
DSK 2
FILL
TIE
TIE
Backup
DIP
MIX
SHIFT
DSK 1
DSK 2
CUT
CUT
PREV
CUT
AUTO
DSK 1
DSK 2
FTB
TRANS
DIP
AUTO
AUTO
MIX
SHIFT
PREV
CUT
AUTO
TRANS
Downstream Keyers and Fade to Black
1
2
3
4
5
6
7
8
9
CAM
0
CLR
Next Transition
The BKGD, KEY 1, KEY 2, KEY 3, KEY 4 buttons are used to select the elements which will transition on air or
ON
ON
ON
ON
off air with the next transition. Any combination of background and keys can be selected by pressing multiple
DSK 1
BKGD
KEY 1
KEY 2
KEY 3
KEY 4
buttons simultaneously. Double-pressing the BKGD button selects all of the next transition upstream keyers
TIE
that are currently on air and copies them to the Next Transition buttons.
DIP
Pressing any of the next transition buttons will clear selection of all others. When selecting the elements of
MIX
the next transition, the switcher operator should look at the preview output because it provides an accurate
representation of what the program output will look like after the transition is completed. When only the
1
2
3
DSK 1
CUT
BKGD button is selected, a transition from the current source on the program bus to the source selected on
4
5
6
the preview bus will occur.
7
8
9
DSK 1
CUT
AUTO
AUTO
ON AIR
CAM
0
CLR
The ON AIR indicator buttons indicate which of the upstream keys are currently on air and can also be used
to immediately cut a key on or off air.
Downstream Keyers
Control Panel
Main
ON
ON
DSK TIE
Backup
Switcher
The DSK TIE button will enable the DSK on the preview output, along with the next transition effects, and tie
Main
DSK 1
DSK 2
KEY 3
KEY 4
TIE
TIE
Backup
it to the main transition control so that the DSK can be taken to air with the next transition.
Because the tied downstream keyer is now tied to the main transition, the transition will happen at the rate
specified in the transition rate display of the transition control block. When the DSK is tied, the signal routing
to the clean feed 1 is unaffected.
DSK 1
DSK 2
CUT
CUT
DSK CUT
The DSK CUT button is used to cut the DSK on or off air and indicates whether the DSK is currently on or off
DSK 1
DSK 2
FTB
AUTO
AUTO
air. The button is illuminated if the DSK is currently on air.
DSK AUTO
The DSK AUTO button will mix the DSK on or off air at the rate specified in the DSK rate window.
Fade to Black
FTB
The FTB button will fade the program output to black at the rate specified in the FTB rate window. Once the
program output has been faded to black, the FTB button will remain illuminated red until it is pressed again,
fading the program output up from black at the same rate. A fade to black cannot be previewed.
Control Panel
Main
Backup
Switcher
Main
DSK 2
TIE
Backup
DSK 2
CUT
DSK 2
FTB
AUTO
Publicidad
