Nussbaum WA 950 Instrucciones De Uso página 80

- Advertising slogan: 4 lines for e.g. your advertising. Will
appear on bottom of printout. To change same as above (also
see movie „Create_advertising_slogan.avi" on software CD).
- Date format: to change between European and US date
format.
European day/month/year: DD.MM.YYYY
Amerikanisch month/day/year: MM.DD.YYYY
7.2.2 Units of Measurement
- Toe:
Degrees: degrees resp. degrees/minutes
Length: millimetres or inches
- Set Back and Track Differen...:
Degrees: degrees resp. degrees/minutes
Length: millimetres or inches
- Length:
millimetres: mm
inches: "
- Angles:
Grades: e.g. 1,50°
Degrees: e.g. 1°30'
- Pressure: (used in and for databank of car).
Bar: e.g. 4,0bar
Psi: e.g. 60psi
- Weight: (used in databank of car)
Kilograms:
Pounds:
- Milage: used for databank of car
Kilometres:
Miles:
- Angle resolution:
hundreths of a degree: e.g. 1,68
tenths of a degree: e.g. 1,7
7.2.3 Printing
- Type:
Alphanumerical: will always be printed with all values.
Vehicle situation: will print the standard values with a
pictogram of toe and camber (together with alphanumerical
report).
Chassis situation: will print report of e.g. axle offset, wheel-
base difference, track difference (together with alphanume-
rical report).
Full: Will print all three reports.
- Customised Logo:
No: no logo will printed
Yes: on Alphanumerical printout our logo will appear on top
right side. Install personal Logo see chapter 7.4.
- Colour printing:
Yes: printout will be colour.
No: printout will be not coloured.
7.2.4 Databank
- Archive: you select in general your car from
Main: main databank
User: User (your self created cars)
Both: both
- Markets: when you start the procedure, you select in general
the cars from this market.
- Make: when you start the procedure, you select in general a car
from this make.
- Sorting:
Alphabetical: the cars in the databank are sorted alphabe-
tical
Date: the cars in the databank are sorted by date
1 689 979 873N 19.03.2010
- Selection by Year:
Yes: when you select the car from databank, you first have to
enter the year of manufacturing – then only cars which are
manufactured in this year are shown.
No: all cars are shown.
- Vehicle description:
Commercial: cars are sorted and shown by commercial (e.g.
MB C-Class series) description.
Manufacturer: cars are sorted and shown by manufactorer
(e.g. MB S203) description.
7.2.5 Job Record
- Type:
Fast: Standard print
Full: is more detailed with tyre pressure, tread depth, and
make of tyre.
- Record Sorting:
Date: sorted by date
Customer: sorted by customer
Vehicle Reg. n.: sorted by vehicle reg. number
Operator: sorted by operator
Order number: sorted by order number
- Enable Modification:
Yes: will allow you to change values of an alignment after-
wards when the job is safed in the databank.
No: You can´t change values.
- Safe work:
Yes: will allow you to safe the results from an alignment
procedure.
No: You can´t safe the results.
7.2.6 Data Summary Screen
- Type: on Data Summary Screen all values of the previous
alignment are displayed.
Static (MB): display of the values according to MB screen
display reauirements
Dynamic: standard indication displayof the values with
green/red (good/bad) indication
7.2.7 Alignment Procedure
- Lift test:
No: no lift test with MercedesBenz lift
Yes: system will start with MercedesBenz lift test when
computer is restarted.
- Vehicle Selection:
Always recalled: You will get automatically after the start to
the selection screen to select car.
Recalled on request: selection screen on request.
- Vehicle Selection Mode:
Databank: choose a car from databank (main, user or both).
Job record: choose a car from from Job records (cars,
which have been already measured and saved to local
databank).
- Rim Diameter:
Always: if toe (see 7.2.2 Toe) is shown in millimitres / inches,
the rim diameter can be controlled always before starting an
alignment procedure.
On request: if toe is shown in millimitres / inches, the rim diameter
can be controlled only if in databank there is no information (on
request) before starting an alignment procedure.
- ROC:
Always: means you have to do the run-out-compensation
always.
Manual skip: you can do the run-out-compensation it or
skip it.
Automatic skip: ROC is skiped always.
77