Install Logo To Starting Screen; Install Logo To Printout - Nussbaum WA 950 Instrucciones De Uso

- Caster Measurement Steering:
Always recalled: steering procedure will come always
(then you still can skip it).
Recalled on Request: you have to recall it from data
summary screen.
If adjustable: steering procedure will come only if some-
thing on caster can be adjusted but from data summary it still
can be recalled.
- Rear:
Always recalled: in procedure after data summary you will
get always to data screen of rear axle.
If adjustable: you only get to data screen rear axle.
- Help measurement:
Enabled: additional picture information's like „insert pedal
brake depressor" or „insert steering wheel holder" are shown.
Disabled: no informations are shown.
7.2.8 Aligner
- Electronic turntable enabling:
Always: go for max. steering angle,
On request: you have to press button, chapter
Never: no max. steering angle (if you use mechanical
turntable)
- Turntable Enabling:
Mechanical:
Electronic:
- Reference Axis:
Symetry: adjust to symmetry of car
Thrust/Travel: adjust to Thrust/Travel of car (not recom-
mended)
Steering wheels straight: the car is adjusted when stee-
ring wheel is centred.
- Previous data saving:
Automatic: Saving automatically
Manual: You have to press the save button every screen
- Caster Measurement Steering:
20 Degress: steering procedure has to go to 20°.
Unrestricted: you can go to 10° (then no steering diffe-
rence is measured) or to 20°.
- Front axle Adjustment:
Caster: when you get to screen front axle values, beside of
toe and camber you get the values either from caster (left/
right).
Total Toe / Set Back: when you get to screen front axle
values, beside of toe and camber you get the values from
Total Toe / Set back.
- Rear axle Adjustment:
Total Toe/Thrust Angle: when you get to screen rear axle
values, beside toe and camber you get the values either from
Total Toe/Thrust Angle or Set Back/Track Difference.
Camber: right / left
Set Back/Track Difference: when you get to screen rear
axle values, beside toe and camber you get the values either
from Total Toe/Thrust Angle or Set Back/Track Difference.
- Thrust Angle:
Positive Clockwise: (normally)
Positive Anticlockwise:
78
7.3

Install Logo to starting screen

(also see movie „Logo_to_Screen.avi" on software CD)
To bring your personal logo to the main screen, you have to
exchange a Bitmap-File. Address of the file, which has to be
exchanged:
C:\Program Files\Alignment\Graphics\Logo\logofew.bmp or
logofef.bmp.
Your logo should be not bigger than width 712 Pixel and height
131 Pixel with a resolution of 96 Pixel/Inch.
The new file with your logo has to be saved under the same name
in the same folder.
When you save your logo with the same name, the old
file gets lost.
After you changed the file in user set-up you have to change the
setting.
7.4

Install Logo to printout

(also see movie „Logo_to_Printout.avi" on software CD)
To bring your personal logo to the printout (on the top right side),
you have to exchange a Bitmap-File. Address of the file which has
to be exchanged:
C:\Program\ Files\Alignment\Graphics\Image\Imgprbarra4.bmp.
Your logo should be not bigger than width 1100 Pixel and height
354 Pixel with a resolution of 72 Pixel/Inch.
The new file with your logo has to be saved under the same name
in the same folder.
When you save your logo with the same name, the old
file gets lost.
After you changed the file in user set-up you have to change the
setting.
19.03.2010 1 689 979 873N