Publicidad
Idiomas disponibles
Idiomas disponibles
EN
Attaching the seat B a-c
Remove the cable ties that secure the seat during
Î
transport.
Fit the seat (dependent on the seat design) on the
Î
seat plate:
a: Seat without adjustment lever:
In the rear area with two screws and in the front
area using two tommy screws with washers.
b: Seat with adjustment lever:
Using 4 flange nuts and 2 washers.
c: Plug the cable connector onto the seat contact
plug
If necessary, attach the cable connector to the
Î
seat contact switch and ensure that the cable is
routed so that it is not damaged or squashed.
Note
The device cannot be started without a con-
nected seat contact switch.
Aligning the upper bow-shaped handle of
the rear frame Bd
The bow-shaped handle is folded down for transport.
Remove the two screws from the rear frame 1 .
Î
Fully fold out the bow-shaped handle 2 .
Î
Attach the bow-shaped handle to the rear frame
Î
using the previously removed screws - tightening
torque 18-27 Nm 3 .
Installing the steering wheel Be
Remove the cover cap [1] from the steering
Î
wheel.
Remove screw [2] and washer [3].
Î
Bring the wheels into a straight position.
Î
Place the steering wheel on the steering shaft.
Î
Position washer [3] with curved face upwards.
Î
Secure the steering wheel using the screw [2].
Î
Put on the cover cap [1].
Î
Fitting the adjusting cylinder of the steering
column adjustment mechanism Bf
Note
Only necessary for devices, where the steer-
ing column adjusting cylinder is not fitted for
transport reasons.
Raise the steering column [B] and maintain it in
Î
position 1 .
Raise the adjusting cylinder [A] and secure it
Î
using shoulder screw [1], washer [2] and flange
nut [3] on the mounting bracket of the steering
column, tightening torque 14-16 Nm 23 .
Note
The shoulder screw, washer and flange nut
are contained in the device's accessories kit
or they are already loosely pre-fitted on the
bracket or adjusting cylinder.
14
Setting up the steering column Bg
Note
Only for devices where the steering column
has been folded down for transport.
Pull the steering column adjustment lever [A] up-
Î
wards and move the steering column [B] into the
desired position 12 .
Release the steering column adjustment lever [A]
Î
to lock the steering column in this position 3 .
Note
Ensure the steering column is correctly
locked/engaged.
The steering column can be set to various
heights. For more on this, please refer to the
section "Operation – Fitting the steering column".
Attaching the trailer coupling (optional;
depending on the model) Bh
Fix the trailer coupling [1] to the rear panel of the
Î
device using screws [2].
Fitting the deflector flap on the cutter
deck Bi (model-dependent)
Remove the ignition key, which is secured to the
Î
mounting of the discharge opening of the cutter
deck with a cable tie (model-dependent).
Remove the screw [1] and nut [2] on the dis-
Î
charge opening of the cutter deck 1 .
Position the deflector flap on the cutter deck so
Î
that the lugs on the deflector flap sit in the re-
cesses on the cutter deck 2 .
Push the deflector flap right back 3 .
Î
Secure the deflector flap with the screw [1] and
Î
nut [2] on the discharge opening of the cutter deck 4 .
Removing the transport lock on the deflec-
tor flap Bj (model-dependent)
Remove the ignition key, which is secured to the
Î
mounting of the discharge opening of the cutter
deck with a cable tie (model-dependent).
Remove the safety plate or the cable ties (de-
Î
pending on the version).
3 The deflector flap closes automatically.
Removing the mulching stopper/mulching
wedge from the cutter deck (model-depen-
dent)
For transport reasons, it may be that, dependent on
the model and version, there is an optional mulching
stopper/mulching wedge in the discharge opening
of the cutter deck. This must be removed from the
discharge shaft prior to start-up of the cutter deck for
conventional mowing (side discharge of the cuttings)
or when operating the device with an optional grass
catcher.
Assembly
Publicidad
