Introduction; About This Document; Personnel Qualifications; Abbreviations Used - Wilo EMU FA Serie Instrucciones De Instalación Y Funcionamiento

English

1. Introduction

1.1. About this document

The language of the original operating manual is
German. All other language versions are transla-
tions of the original German manual.
This manual is divided into individual chapters,
which can be viewed in the table of contents.
Each section has a heading which clearly de-
scribes its content.
A copy of the EC declaration of conformity is
a component of these operating instructions.
If a technical modification is made on the designs
named there without our agreement, this decla-
ration loses its validity.

1.2. Personnel qualifications

All personnel who work on or with the pump must
be qualified for such work; electrical work, for
example, may only be carried out by a qualified
electrician. All personnel must be of legal age.
Operating and maintenance personnel must also
observe national accident prevention regulations.
It must be ensured that personnel have read and
understood the instructions in this operating and
maintenance handbook; if necessary, this manual
must be ordered from the manufacturer in the
required language.
This pump is not intended for use by persons
(including children) with limited physical, sensory
or mental capacities or without the relevant
experience or knowledge, unless they are super-
vised by a person responsible for their safety and
receive instructions from this person on how to
use the pump.
Children must be supervised in order to ensure
that they do not play with the pump.

1.3. Abbreviations used

• approx. = approximately
• e.g. = for example
• etc. = and so on
• i.e. = that means
• if nec.= if necessary
• incl. = including
• max. = maximum
• min. = minimum
• p.t.o. = please turn over
• poss. = possibly
• re. = regarding
• s.a. = see also

1.4. Copyright

This operation and maintenance manual has been
copyrighted by the manufacturer. The operation
and maintenance manual is intended for use by
installation, operating and maintenance per-
sonnel. It contains technical specifications and
diagrams which may not be reproduced or dis-
tributed, either completely or in part, or used for
any other purpose without the express consent
of the manufacturer. The illustrations used may
differ from the original and are only intended as
an exemplary representation of the pumps.
44

1.5. Rights of alteration

The manufacturer reserves the right to make
technical alterations to systems or components.
This operating and maintenance manual refers to
the pump shown on the title page.

1.6. Warranty

This section contains the general information on
the warranty. Contractual agreements have the
highest priority and are not superseded by the
information in this section.
The manufacturer is obliged to correct any de-
fects found in the pumps it sells, provided that
the following requirements have been fulfilled.
1.6.1. General
• The defects are caused by the materials used
or the way the product was manufactured or
designed.
• The defects were reported in writing to the man-
ufacturer within the agreed warranty period.
• The pump was used only as prescribed.
• All safety and control devices were connected and
inspected by qualified personnel.
1.6.2. Warranty period
If no other provisions have been made, the war-
ranty period applies to the first 24 months after
commissioning or to a max. period of 30 months
after the delivery date. Other agreements must be
made in writing in the order confirmation. These
remain valid at least until the agreed warranty
period of the pump has expired.
1.6.3. Spare parts, add-ons and modifications
Only genuine spare parts from the manufacturer
may be used for repairs, replacements, add-ons
and modifications. Unauthorized add-ons and
modifications or the use of non-original spare
parts can seriously damage the pump and/or
injure personnel.
1.6.4. Maintenance
The prescribed maintenance and inspection
work should be carried out regularly. This work
may only be carried out by qualified, trained and
authorized personnel.
1.6.5. Damage to the product
Damage and malfunctions that endanger safety
must be eliminated immediately by trained
personnel. The pump may only be operated if it
is in perfect working order. During the agreed
warranty period, the pump may only be repaired
by the manufacturer or an authorized service
center. The manufacturer reserves the right to ask
the operator to return the damaged pump to the
factory for inspection.
1.6.6. Exclusion from liability
No warranty claims will be accepted or liability
will be assumed for pump damage if any of the
following items apply:
INTRODUCTION
WILO SE 05/2014 v05 DIN A4