Maintenance - Scheppach CSP41 Traducción De La Instrucción De Original

9. Maintenance

Air filter (Fig.16-17)
• Clean the air filter after each use.
• Unscrew the air filter mounting nut and remove
the cover.
• Remove the air filter .
• Open the air filter with a screwdriver.
• Clean the air filter. Wash the filter in clean, warm,
soapy water. Let the air dry completely.
• Insert the air filter. Put on the cover of the engine /
air filter. Make sure the cover is installed correctly.
Tighten the screw that secures the cover.
m NOTICE
It is advisable to keep a stock of spare filters.
Oil supply opening (Fig.21)
• Check the oil supply opening (K) after each use.
• Dissemble the bar.
• Check the oil outlet (K) for obstructions.
Bar (Fig. 25)
• Clean the bar after each use.
• Remove the bar from the machine.
• Remove sawdust from the bar and the oil channel .
• Lubricate the teeth (Fig.23/Pos.2/3) through the
oiling hole with an oil syringe.
Cylinder fins (Fig.23)
• Clean the cylinder fins (M) after each use. To do
this, use compressed air at low pressure or use
a brush.
• Dust and dirt between the fins on the cylinder may
cause the machine to overheat.
Other maintenance points before each use
• Check for leakage from oil or fuel tanks.
• Check the unit for loose parts and screws. Specifi-
cally, the chain, the bar and the hand grips.
• If you find defects on the machine, fix them im-
mediately.
Fuel filter (Fig.21)
m CAUTION!: Never operate the saw without the fu-
el filter (L). After every 100 hours of operation the fu-
el filter needs to be cleaned or replaced when dam-
aged. Drain the fuel tank completely before replac-
ing the filter.
• Remove the fuel tank cap .
• Make a handle from soft wire.
• Insert it into the opening of the fuel tank and hook
the fuel hose. Pull the fuel hose carefully to the
opening until you can grab it with your fingers.
46 І 164
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
m NOTICE
Pull the hose so it is not quite out of the tank.
• Lift the fuel filter (L) from the tank.
• Remove the filter with a twisting motion and clean
it. If it is damaged, discard the filter.
• Insert the cleaned filter or a new one. Plug one end
of the filter into the tank opening.
• Make sure the filter is seated in the lower tank cap.
Move the filter with a long screwdriver to put it in
its proper slot.
• Fill the tank with fresh fuel mixture. Put the cap
on the tank.
Spark plug (Fig. 24)
m NOTE!: In order for the saw motor to remain pow-
erful, the spark plug must be clean and properly
gapped (0.6 mm). Spark plugs should be cleaned or
replaced every 20 hours.
• Set the power switch (10) to „Stop (0)".
• Remove the air filter cover (9) by removing the
air filter mounting nut . The cover can then be re-
moved.
• Disconnect the spark plug from the ignition wire by
gently pulling it and turning the spark plug .
• Remove the spark plug with a spark plug wrench.
Do not use other tools.
• Clean the spark plug with a copper wire brush or
replace it with a new one.
Carburetor setting
The carburetor has been set to its perfect adjustment
at the factory. If it requires adjusting, take the saw
to your nearest authorized after-sales service outlet.
m WARNING!: You may not make settings on the
carburetor itself!
Bar
• Check after every 8 hours of work to ensure uni-
form wear.
Chain
Chain Tension
Periodically check the chain tension and adjust if
necessary, so that after use the chain is snug against
the rail, but still loose enough that it can be pulled by
hand. (Fig.8)
Breaking in a new saw chain
A new chain and bar will need chain readjustment af-
ter as few as 5 cuts. This is normal during the breakin
period, and the interval between future adjustments
will begin to lengthen quickly.
Chain lubrication
Always make sure the automatic oiler system is
working properly. Keep the oil tank filled with Chain,
Bar and Sprocket Oil.
Adequate lubrication of the bar and chain during cut-
ting operations is essential to minimize friction with