Gemini 810 DIODE LASER Manual Del Usuario página 14

ELECTROMAGNETIC ENVIRONMENT GUIDANCE
NOTES
The higher frequency range applies at 80 MHz and 800 MHz.
Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast, cannot be
predicted theoretically with accuracy. An investigation of the location is recommended to determine the electromagnetic environment resulting from stationary HF transmitters. If the measured field
strength in the location in which the Gemini 810 + 980 diode laser is used exceeds the applicable RF compliance level above, the Gemini laser unit should be observed to verify normal operation. If
unusual performance characteristics are observed, it may be necessary to take additional measures such as reorientation or repositioning of the Gemini 810 + 980 diode laser.
Over the frequency range 150kHz to 80MHz, field strengths should be less than 3V/m.
WORKING CLEARANCES
The Gemini 810 + 980 diode laser is intended for operation in an electromagnetic environment where radiated HF interference is checked. The customer or the user of the Gemini laser can help prevent
electromagnetic interference by duly observing the minimum distances between portable and/or mobile RF communication devices (transmitters) and the Gemini laser unit. These values may vary
according to the output power of the relevant communication device as specified below.
RATED MAXIMUM OUTPUT
POWER OF TRANSMITTER [W]
0.01
0.1
1
10
100
For transmitters whose maximum nominal output is not specified in the above table, the recommended working clearance d in meters (m) can be determined using the equation in the corresponding
column, where P is the maximum nominal output of the transmitter in watts (W) specified by the transmitter manufacturer.
Remark 1: The higher frequency range applies at 80 MHz and 800 MHz.
Remark 2: These guidelines may not be applicable in all cases. The propagation of electromagnetic waves is influenced by their absorption and reflection by buildings, objects and persons.
WARRANTY
Seller warrants the Products to be free from defects in materials and workmanship for a period of two years from the date of shipment, except for consumables. If within
such period any Products shall be proved to Seller's satisfaction to be defective, it shall be (i) repaired using new or refurbishing parts, or (ii) replaced with a new or
refurbished product, at Seller's sole discretion. Such repair or replacement shall be Seller's sole obligation and Buyer's exclusive remedy under this Warranty and shall
be conditioned, at Seller's option, upon return of such Products to Seller, f.o.b. its factory. This Warranty only covers Product issues caused by defects in material or
workmanship during ordinary consumer use; it does not cover Product issued caused by any other reason, including but not limited to acts of God, modifications of or
to any part of the Product, improper testing, assembly, mishandling, misusue, neglect, adjustments, alterations to the products, improper operation contrary to current
instructions relating to installation, maintenance or operation, or contrary to industry standards relationg to acceptable input power.
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER REPRESENTATIONS AND WARRANTIES, EXPRESS OR IMPLIED; AND SELLER EXPRESSLY DISCLAIMS AND EXCLUDES ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. SELLER SHALL HAVE NO OBLIGATION OR LIABILITY TO REFUND ANY PORTION OF THE
PURCHASE PRICE AND SHALL NOT BE LIABLE FOR ANY SPECIAL, EXEMPLARY, INCIDENTAL, CONSEQUENTIAL OR PUNITIVE DAMAGES OR LOST PROFITS, OR DAMAGE TO PERSONS
OR INJURY IN CONNECTION WITH THE PURCHASE OR USE OF THE INSTRUMENT.
14
WORKING CLEARANCE ACCORDING TO TRANSMISSION FREQUENCY [M]
150 KHZ TO 80 MHZ 80 MHZ TO 800 MHZ
d= [1.2] √P
0.12
0.38
1.2
3.8
12
800 MHZ TO 2.5 GHZ
d= [1.2] √P
d= [2.3] √P
0.12 0.23
0.38 0.73
1.2 2.3
3.8 7.3
12 23