Publicidad
1.
GENERAL INFORMATION
1.1.
PURPOSE OF THIS MANUAL ..................................................
1.2.
MANUFACTURER AND MACHINE IDENTIFICATION ..............
1.3.
CUSTOMER SERVICE RECOMMENDATIONS ........................
2.
SPECIFICATIONS
2.1.
GENERAL MACHINE DESCRIPTION .......................................
2.2.
OPERATING CONDITIONS AND
CONTRARY DIRECTIONS .....................................................
2.3.
SPECIFICATIONS ....................................................................
2.4.
SAFETY DEVICES ...................................................................
2.5.
WORKING PLACES ..................................................................
2.6.
NOISE LEVEL ............................................................................
3.
SAFETY PRECAUTIONS
(SAFE WORKING PRACTICES)
3.1.
SAFETY REGULATIONS...........................................................
3.2.
RESIDUAL RISKS .....................................................................
3.3.
SAFETY AND INFORMATION SIGNALS .................................
4.
INSTALLATION
4.1.
LIFTING AND UNLOADING ......................................................
4.2.
INSTALLATION AREA - CHARACTERISTICS .........................
4.3.
UNPCKING ................................................................................
4.3.1 Operating units blocking .....................................................
4.3.2 Glue spreader roller oscillation locking ......................................
4.4.
INSTALLATION OF DISASSEMBLED PARTS ..........................
4.4.1. Reel Holder ................................................................................
4.4.2. Montaggio prolunghe piano ................................................
4.5.
ELECTRICAL CONNECTION ....................................................
4.6.
PNEUMATIC CONNECTION .....................................................
4.7.
COLLEGAMENTO ASPIRAZIONE ............................................
5.
SET-UP PROCEDURES
5.1.
ADJUSTING THE PRESSURE OF THE
PNEUMATIC SYSTEM............................................................
5.2.
ADJUSTING REGISTRABLE ENTRANCE GUIDE ...................
5.3
Fitting the edging strip ................................................................
5.4
ADJUSTING FEEDER HEIGHT ................................................
5.5
ADJUSTING ADJUSTABLE INFEED PRESSER ROLLER
UNITS ........................................................................................
5.6.
END TRIMMING REGULATION ................................................
5.7.
TRIMMING REGULATION .........................................................
5.8.
ADJUSTING THE FEELER PIN OF THE BOARD CUTTER .....
5.9.
ADJUSTING THE FEELER PIN OF THE EDGE SCRAPING
CUTTER ..................................................................................
5.10. BRUSH UNIT .............................................................................
5.11. SUBSTITUTION OF TOOL ........................................................
5.11.1 Substituting knife for reel cutting shears ....................................
5.11.2 Replacing the end trimmer blade ......................................
5.11.3 Substitute blades in upper and lower board cutting knives ........
5.11.4 Replacing edge scraper inserts .........................................
5.11.5 Replacing the brushes .........................................................
5.12. ADJUSTING THE AMOUNT OF GLUE ON THE PANEL ..........
INDEX
6.
OPERATING PROCEDURES
10
6.1.
DESCRIPTION OF COMMANDS .............................................
12
6.1.1 Control functions .......................................................................
14
6.1.2 Starting the machine .................................................................
6.1.3 Stopping the machine ...............................................................
6.1.4 Emergency stop ........................................................................
6.1.5 Setting glue temperature ..........................................................
16
6.1.6 Setting Standby Time ................................................................
6.2.
MACHINE PREPARATION AND USE ......................................
6.3.
EDGES FOR SMALL SIZE PANELS ........................................
20
22
6.4.
SUGGESTIONS FOR USE ......................................................
26
26
7.
MAINTENANCE REQUIREMENTS
28
7.1.
SPECIAL SUBSTITUTIONS .....................................................
7.2.
END TRIMMER BELT - REPLACEMENT .................................
7.3.
TRIMMER BELT - REPLACEMENT .........................................
30
7.4.
REPLACING THE FEEDER BELT ............................................
36
7.5.
ADJUSTING TENSION OF FEEDING BELT ............................
38
7.6.
GENERAL CLEANING ............................................................
7.7.
CHANGING THE GLUE ...........................................................
7.8.
GENERAL LUBRICATION ........................................................
7.9.
SHARPENING OF TOOLS .......................................................
7.10. CHECKING THE SAFETY DEVICES .......................................
42
7.11. DISCARDING THE MACHINE ..................................................
44
46
8.
TROUBLE - SHOOTING GUIDE
46
46
48
8.1.
TROUBLES - CAUSES - WHAT TO DO ...................................
48
48
50
54
54
56
56
58
62
62
64
64
68
70
72
72
74
74
76
78
78
80
- 6 -
ENGLISH
82
82
84
86
86
86
88
88
98
98
102
102
104
104
108
108
110
112
114
114
114
116
Publicidad
