Setup Functions; Pc-Keyboard; Technical Data; Lift - Nussbaum WAB 02 CCT Instrucciones De Uso

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

10.5

Setup functions

Starts / Stops the demo mode for the aligner.
Enter the setup menu
Exit to Windows.
10.6

PC-Keyboard

There are some shortcuts on the keyboard for quick access.
Key(s)
F12 _____________________________________________ Help
Shift+F1 _________________________ Robot selection screen
Shift+F12 _____________ Version display on the main screen
11.

Technical Data

11.1

Lift

Base model: UNILIFT 3500 CLT
Runway length
Load capacity
Runway height
Max.Over all length
Max.Over all width
Cabinet
Computer Celeron
Harddisk
Network Ethernet
DVD drive
RS232
USB
Sound card on board
Monitor 17"
Printer
Max.dimensions
Load distribution
Raising time lift
Lowering time lift
Max. Lifting height:
Operating voltage
Motor power
Motor rpm
Pump capacity oil pump
Pressure relief valves
Filling quantity oil
Noise level
Electrical wall outlet
102
Function
5000 mm
3500kg
220 mm
6320 mm
3350 mm
3,0 GHz,
10/100
Colour inkjet
1,60 x 0,60 x 0,60 m
max. 2:1 right/left or left/right
ca. 31 sec. with nominal load
ca. 17 sec. with nominal load
1930 mm
3 x 400 Volt , 50Hz
3 kW
3000 turns / Minute
3 ccm
approx. 320 bar (lifting)
approx. 120 bar (plates)
approx. 40 bar (SST nut)
approx. 40 Liter
75 dBA
3~/N+PE, 400V, 50 Hz
with breakers T16A
according to local regulations
11.2

Wheel Alignment:

Load capacity turntables
Wheel diameters (outside)
Total toe
Individual toe
Camber
Setback
Thrust angle
Caster
KPI / SAI
TOOT
Max.Steering
11.3
Sicherheitseinrichtungen Hebebühne
1.
Pressure relief valves
Protects against excess pressures in hydraulic system
2.
Check valves
Protects vehicles against unintended descend
3.
CE-Stop
Protection against squeezing feet under the lift
4.
Hydraulically unlockable SST nut safely blocks lift in all height
position.
5.
Interactive Safety system:
-
Plate/Lift controller monitors all of the raising/lowering pro-
cess.
-
Lift lowers in normal operation equalized with 0.05 Meter per
Second. If speed increases e.g. due to a defect of the
hydraulic system, the Plate/Lift controller will detect this
problem and will release the blocking nut. The safety cutoff
gets triggered and the lift stops.
-
Der Hauptschalter ist auszuschalten.
-
The entire hydraulic system is to be checked. If there are
defects, the after sales service is to be called.
80 GB
-
The lift can be maintained and repaired by personnel special-
ly trained by the manufacturer.
2
6
CE-STOP (Lift)
-
In a height of 320 mm above the floor (valid for on-ground and
in-ground installation) the lift will automatically stop lowering.
-
You have to check that there are no persons or objects in the
area below the lift.
-
You press „Down" once more, and keep it depressed until the
lift is fully down, and the audible signal stops by itself.
Automatic Height Cutoff
-
When the lift reaches the maximum permissible height, it will
stop automatically.
1500 kg
450..750mm
+/-10° (+/-2'Resolution)
+/-5° (+/-1'Resolution)
+/-5° (+/-1'Resolution)
+/-3° (+/-2'Resolution)
+/-3° (+/-2'Resolution)
+/-24° (+/-9'Resolution)
+/-24° (+/-9'Resolution)
+/-24° (+/-5'Resolution)
+/-60° (+/-8'Resolution)
29.10.08
AD G9001 N

Publicidad

Tabla de contenido
loading

Tabla de contenido