Tabla De Contenido - Honda Motor BF40D Manual Del Usuario

INDEX
1. SPECIFICATIONS........................................................ 1-1
1. SPECIFICATIONS .................................................. 1-1
2. DIMENSIONAL DRAWINGS ................................ 1-5
1
2. SERVICE INFORMATION ........................................... 2-1
2
1. THE IMPORTANCE OF PROPER SERVICING...... 2-1
2. IMPORTANT SAFETY PRECAUTIONS ................ 2-1
3
3. SERVICE RULES ................................................... 2-2
4. SYMBOLS USED IN THIS MANUAL ................... 2-3
4
5. SERIAL NUMBER LOCATION .............................. 2-3
6. STARTING PROCEDURE AFTER INSTALLING
5
THE ENGINE ......................................................... 2-4
7. MAINTENANCE STANDARDS............................. 2-5
8. TORQUE VALUES................................................. 2-9
6
9. SPECIAL TOOLS ................................................. 2-12
10. TROUBLESHOOTING ......................................... 2-18
7
a. FUSE ................................................................ 2-18
FUSE BOX CONNECTING TABLE ................. 2-18
8
FUSE LOAD CHART........................................ 2-19
b. ENGINE............................................................ 2-20
9
HARD STARTING............................................ 2-20
POWER SYSTEM ............................................ 2-22
10
STARTER SYSTEM ......................................... 2-23
FUEL SYSTEM ................................................ 2-25
11
IGNITION SYSTEM ......................................... 2-27
ENGINE DOES NOT RUN SMOOTHLY......... 2-28
12
SPARK TEST ................................................... 2-33
OIL PRESSURE CHECK .................................. 2-33
13
CYLINDER COMPRESSION CHECK............... 2-34
c. ALERT SYSTEM/WARNING SYSTEM........... 2-35
SYMPTOM CHART ......................................... 2-35
14
OIL ALERT SYSTEM ....................................... 2-35
OVERHEAT ALERT SYSTEM ......................... 2-35
15
ALTERNATOR WARNING SYSTEM .............. 2-35
MIL WARNING SYSTEM................................ 2-35
16
FUNCTION TEST USING HDS (Dr. H OR
POCKET TESTER) ........................................... 2-36
17
FUNCTION TEST WITHOUT USING HDS
(Dr. H OR POCKET TESTER) .......................... 2-37
18
WARNING BUZZER SOUNDS
CONTINUOUSLY ............................................ 2-40
19
INTERMITTENT SOUND OF WARNING
BUZZER KEEPS SOUNDING.......................... 2-44
20
ECM IS ABNORMAL....................................... 2-46
d. SHIFT MECHANISM ....................................... 2-47
HARD TO SHIFT THE GEAR........................... 2-47
e. GAS ASSISTED DAMPER [GAS ASSISTED
TYPE ONLY] .................................................... 2-49
TILT-UP LOAD IS HEAVY .............................. 2-49
GAS ASSISTED DAMPER DOES NOT HOLD
IN POSITION ................................................... 2-49
f. POWER TRIM/TILT [POWER TRIM/TILT
TYPE ONLY] .................................................... 2-50
POWER TRIM/TILT ASSEMBLY DOES NOT
MOVE............................................................... 2-50
POWER TRIM/TILT ASSEMBLY DOES NOT
HOLD IN POSITION ........................................ 2-51
POWER TRIM/TILT MOTOR DOES NOT
OPERATE......................................................... 2-52
POWER TRIM/TILT ASSEMBLY QUICK
REFERENCE CHART ....................................... 2-53
g. METERS........................................................... 2-55
TACHOMETER DOES NOT OPERATE
PROPERLY....................................................... 2-55
TRIM METER DOES NOT OPERATE PROPERLY
[POWER TRIM/TILT TYPE ONLY] .................. 2-56
11. CABLE/HARNESS ROUTING ............................. 2-57
12. TUBE ROUTING.................................................. 2-81
13. LUBRICATION POINTS ...................................... 2-89
3. MAINTENANCE .......................................................... 3-1
1. MAINTENANCE SCHEDULE ................................ 3-2
2. ENGINE OIL........................................................... 3-3
3. OIL FILTER CARTRIDGE ....................................... 3-5
4. GEAR CASE OIL.................................................... 3-6
5. SPARK PLUGS ...................................................... 3-8
6. VALVE CLEARANCE ............................................. 3-9
7. FUEL STRAINER [HIGH PRESSURE SIDE] ....... 3-12
8. FUEL STRAINER [LOW PRESSURE SIDE] ........ 3-13
9. IDLE SPEED ......................................................... 3-16
10. THROTTLE CABLE .............................................. 3-17
11. SHIFT CABLE ...................................................... 3-20
12. TIMING BELT ...................................................... 3-24
13. STEERING FRICTION [TILLER HANDLE
TYPE ONLY] ........................................................ 3-26
14. REMOTE CONTROL LEVER FRICTION [SIDE
MOUNT REMOTE CONTROL BOX ONLY] ....... 3-27
4. COVER......................................................................... 4-1
1. ENGINE COVER.................................................... 4-2
2. SEPARATE CASE ................................................. 4-3
5. PROGRAMMED-FUEL INJECTION............................ 5-1
1. SERVICE PRECAUTIONS ..................................... 5-2
• PROGRAMMED-FUEL INJECTION
TROUBLESHOOTING ....................................... 5-2
• FUEL LINE SERVICE ......................................... 5-2
• CHECK AFTER OPERATION............................. 5-3
• FUEL LEAK CHECK ........................................... 5-3
• WHEN THE BOAT IS EQUIPPED WITH RADIO
EQUIPMENT/D-GPS.......................................... 5-3
2. VACUUM CONNECTIONS ................................... 5-4
3. CIRCUIT DIAGRAM............................................... 5-5
4. COMPONENT LOCATION .................................... 5-7
• ECM TERMINAL ARRANGEMENT .................. 5-9
2